User manual SONY PDW-1500

[. . . ] PROFESSIONAL DISC RECORDER PDW-1500 OPERATION MANUAL [English] 1st Edition (Revised 1) WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. THIS APPARATUS MUST BE EARTHED. CAUTION The apparatus shall not be exposed to dripping or splashing and no objects filled with liquid, such as vases, shall be placed on the apparatus. [. . . ] Depending on which button you pressed, this sets the IN point or OUT point, and the IN indicator or OUT indicator lights. To change both the IN point and the OUT point, repeat steps 3 and 4. Carry out steps 1 to 4 in the procedure, "Moving a sub clip" (page 65). Use the arrow buttons to select DELETE, and press the SET button. The sub clip deletion screen appears. 66 5-2 Basic Operations 5-3 Clip List Operations 5-3-1 Displaying the CLIP Menu Proceed as follows. Notes · The CLIP menu can handle up to 99 clip lists. · Do this operation in stop mode. To cancel the deletion, and escape from the sub clip deletion screen Do either of the following. · Use the left or right arrow button to select CANCEL, and press the SET button. The screen returns to the sub clip thumbnail display. With the THUMBNAIL button off, hold down the SHIFT button and press the SUBCLIP button. The CLIP menu appears. CLIP MENU LOAD SAVE DELETE CLEAR TC PRESET 3 Chapter 5 Scene Selection Use the left or right arrow button to select OK, and press the SET button. This deletes the sub clip, and the screen returns to the sub clip thumbnail display. Use this menu to carry out the following operations. · Save the current clip list to disc. · Load a clip list on disc into the current clip list. · Set the start timecode of the current clip list. 5-3-2 Saving the Current Clip List to Disc Saving edited clip lists to disc The operations described above (moving, trimming, and deleting sub clips) are carried out on the current clip list. Execute the procedure in 5-3-2 "Saving the Current Clip List to Disc" (page 67) to save the current clip list to disc again as a clip list. Note Proceed as follows. 1 In the CLIP menu, use the up and down arrow buttons to move the cursor to SAVE and press the right arrow button. "NEW FILE" is shown for lists which do not exist on the disc, having names only. The date of creation or the title of each clip list is shown in the list of clip lists. (The date of creation is always shown for clip lists without titles. ) To switch between the date and the title Hold down the SHIFT button and press the SET button. Unless the current clip list has been saved to disc, its contents will be lost when a disc is ejected or the unit is powered off. After creating a clip list, be sure to save it. 5-3 Clip List Operations 67 CLIP MENU SAVE E0001 E0002 E0003 E0004 E0005 E0006 E0007 E0008 E0009 E0010 CLIP MENU LOAD E0001 E0002 E0003 E0004 E0005 E0006 E0007 E0008 E0009 E0010 04/08/08 21:57 04/08/24 11:15 04/08/25 15:30 NEW FILE NEW FILE NEW FILE NEW FILE NEW FILE NEW FILE NEW FILE 04/08/08 21:57 04/08/24 11:15 04/08/25 15:30 NEW FILE NEW FILE NEW FILE NEW FILE NEW FILE NEW FILE NEW FILE 2 Use the up and down arrow buttons or the jog dial to select the desired clip list, and press the right arrow button. A confirmation message like the one shown below appears. SAVE CLIP LIST 2 Use the up and down arrow buttons or the jog dial to select the desired clip list, and press the right arrow button. A confirmation message like the one shown below appears. LOAD CLIP LIST Chapter 5 Scene Selection SAVE E0005 OK? LOAD E0002 OK? SAVE : TO MENU : SET KEY MENU KEY LOAD : TO MENU : SET KEY MENU KEY 3 Press the SET button. The current clip list is saved to disc. 3 Press the SET button. [. . . ] Non-audio General term for audio signals other than linear PCM, such as Dolby E 1) and Dolby Digital (AC-3). 1) XDCAM can record non-audio as an input signal. 1) Dolby is a trademark of Dolby Laboratories. Proxy AV data Low-resolution data with a video bandwidth of 1. 5 Mbps and an audio bandwidth of 64 kbps per channel. This unit records proxy AV data automatically whenever highresolution MPEG IMX or DVCAM data is recorded. Reference video signal A video signal that contains a sync signal or sync and burst signals, used as a reference for synchronization of video equipment. An interface standardized as SMPTE 259M which enables the transmission of an uncompressed digital component stream. [. . . ]