User manual SONY PDWV1OP

[. . . ] PROFESSIONAL DISC RECORDER PDW-V1 OPERATION MANUAL [English] 1st Edition (Revised 1) WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. THIS APPARATUS MUST BE EARTHED. CAUTION The apparatus shall not be exposed to dripping or splashing and no objects filled with liquid, such as vases, shall be placed on the apparatus. [. . . ] The selected clip list is loaded into the current clip list. 1 With the THUMBNAIL button off, hold down the SHIFT button, and press the SUBCLIP button. The CLIP menu appears. CLIP MENU LOAD SAVE DELETE CLEAR TC PRESET Moving a sub clip Proceed as follows. 1 2 Press the SUBCLIP button, turning it on. Press the THUMBNAIL button, turning it on. Thumbnails of the sub clips within the current clip list appear. 48 5-2 Basic Operations The sub clip movement screen appears. The sub clip selected in step 3 appears surrounded by a frame. This shows that third sub clip is moved to the position of eighth sub clip. To escape from the thumbnail display to the fullscreen display Press the THUMBNAIL button, turning it off. 3 Use the arrow buttons or jog dial to select the desired sub clip. You can select sub clips with the following operations. Press the PREV or NEXT button: Move to the previous or next sub clip. Press the PREV or NEXT button with the SHIFT button held down: Move to the first or last sub clip. Press the F or f button with the SHIFT button held down: Switch to the previous or next page. Cursor showing the position to which the selected sub clip is moved Chapter 5 Scene Selection To escape from the sub clip movement screen to the previous screen Press the RESET button. 6 4 Hold down the SHIFT button, and press the SET button. The sub clip operation menu appears. Use the arrow buttons or the jog dial to move the cursor to the position where you want to move the selected sub clip. Note You can press the THUMBNAIL button to return to full-screen sub clip display, without moving a sub clip. 7 Press the SET button. The sub clip thumbnail display appears, and you can check the new position of the sub clip. To return to the thumbnail display without moving the sub clip Do either of the following. · Use the arrow buttons to select EXIT, and press the SET button. · Press the RESET button. 5 Use the arrow buttons to select MOVE, and press the SET button. Trimming a sub clip Proceed as follows. 5-2 Basic Operations 49 1 2 Carry out steps 1 to 4 in the procedure, "Moving a sub clip" above. Use the arrow buttons to select TRIM, and press the SET button. The first frame of the selected sub clip appears in a full-screen display. In this state, you can carry out playback and search within the clip including the selected sub clip. This carries out the trimming, and the screen returns to the sub clip thumbnail display. To cancel the trim operation Reset the IN point and the OUT point to return to the state before the sub clip trimming screen was displayed, then hold down the SHIFT button and press the SET button. To cancel the trim and escape from the sub clip trim screen Hold down the SHIFT button and press the SET button. Chapter 5 Scene Selection Deleting a sub clip Proceed as follows. 3 4 Carry out playback and search to find the new location of the IN point or OUT point of the selected sub clip. At the point where you want to set the new IN point or OUT point, hold down the G/IN button (when changing the IN point) or the g/OUT button (when changing the OUT point), and press the SET button. Depending on which button you pressed, this sets the IN point or OUT point, and the IN indicator or OUT indicator lights. To change both the IN point and the OUT point, repeat steps 3 and 4. To reset the IN point or OUT point, hold down the G/IN button or the g/OUT button and press the RESET button. The IN point and the OUT point return to the state before the sub clip trimming screen was displayed. [. . . ] This unit records proxy AV data automatically whenever highresolution MPEG IMX or DVCAM data is recorded. Reference video signal A video signal that contains a sync signal or sync and burst signals, used as a reference for synchronization of video equipment. An interface standardized as SMPTE 259M which enables the transmission of an uncompressed digital component stream. The relation of the strength of the desired signal to the accompanying electronic interference, the noise. [. . . ]