User manual SONY CLIE PEGA-AC10 DATASHEET

[. . . ] 7 HDD Network Audio Component CLIE PEGA-AC10 This manual explains the basic connections and operations that will allow you to enjoy music on your GIGA JUKE. For a fuller explanation of the various operations, refer to the supplied Operating Instructions. Using the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . Back cover © 2007 Sony Corporation Connections Connect the AM loop antenna. Connect the AM loop antenna to the AM antenna terminals on the unit. Pull on the cord lightly afterwards to confirm that the antenna is firmly connected. Notes Make sure not to wind the FM wire antenna up during use. [. . . ] After connecting the FM wire antenna, lay it out so that it is as parallel to the floor as possible. Connect the amplifier. Use the supplied audio connecting cord to connect the ANALOG OUT 1 jacks of the unit to the input jack (TAPE, MD, etc. ) of the amplifier. Make sure to match the color-coded cords to the appropriate jacks of the unit; red (right) to red and white (left) to white. Notes Make sure to keep the AM loop antenna away from the unit or other AV equipment as this may produce noise in the radio reception. Make sure the metal leads (not the part covered with vinyl insulation) are securely inserted into the antenna terminals. Connect the FM wire antenna. Connect the FM wire antenna to the FM antenna jack on the unit. FM wire antenna : Signal flow Audio connecting cord (supplied) To the input jack (TAPE, MD, etc. ) of the amplifier GB When connecting the unit to a digital amplifier or other digital component Connect the power cord. Connect the power cord to a wall outlet after all other connections have been made. The unit turns on automatically and starts making the initial settings. The initial settings may take a few minutes depending on the unit's condition. You can connect a digital amplifier or other digital component to the DIGITAL COAXIAL OUT jack or DIGITAL OPTICAL OUT connector of the unit. Refer to page 80 of the operating instructions for details. Connect the unit to a network. If you have a network environment, you can easily connect the unit to the Internet as shown in the figure below. Disconnect the network cable from your computer. WARNING Do not disconnect the power cord while the initial setup is in progress. Doing so may cause the unit to malfunction. Inserting the batteries into the remote control Insert two size-AA (R6) batteries (supplied) into the remote control with the and terminals matching the polarity markings. Plays tracks in a selected folder, such as My library or a newly created folder. Plays a selected playlist of your favorite tracks. 1 Press repeatedly until "Mode" directory (a list of listing modes) appears. Continued 11GB Using the Hard Disk Drive (continued) Press / to select the listing mode. / Press ENTER to enter the listing mode. E. g. , When you select the album mode ENTER Press // to select the desired album or track. // Press ENTER. The unit starts playing in the selected listing mode. ENTER 1GB Transferring~Transferringtrackstoa"WALKMAN"~ Note With the procedure below, you may not be able to transfer tracks in the case of some "WALKMAN" models. In this case, select USB storage device as the transfer destination. Refer to page 48 of the Operating Instructions for details. Refer to http://support. sony-europe. com/ (for the customers in Europe only) for the compatible "WALKMAN" models. 1 Connect the "WALKMAN" to the USB connecting jack of the unit. Make sure that the unit is in the HDD JUKEBOX function. USB connecting jack Press TRANSFER. Up to 30 of the most recently recorded or imported groups (albums) are automatically selected. TRANSFER Press TRANSFER. The selected groups are transferred to the "WALKMAN". TRANSFER When transferring audio data the next time Groups that were recorded or imported to the HDD Jukebox following the last transfer are selected (except for the groups that had been previously transferred). To transfer audio data to other devices You can transfer tracks to another device by assigning the device to the TRANSFER button or selecting it as the destination from the menu. Refer to page 46 of the Operating Instructions for details. 1GB Using the Internet O Obtainingtitleinformation Through an Internet connection, you can obtain title information to albums that were not labeled when you recorded or imported them. Albums saved to the HDD Jukebox can be automatically labeled. For details on obtaining title information to an album: See page 15 1GB Obtainingtitleinformation~Obtainingtitleinformationforanalbum storedintheHDDJukebox~ This section explains how title information (album name, artist name, etc. ) is obtained for albums in the HDD Jukebox. 1 Select the album whose information you are looking for. Press OPTIONS to display the Option menu. OPTIONS Press // / to select [Obtain title info] ­ [Album] and press ENTER. The search starts. When the search is completed, the results are displayed. [. . . ] Press OPTIONS to display the Option menu. OPTIONS Press // / to select [Obtain title info] ­ [Album] and press ENTER. The search starts. When the search is completed, the results are displayed. The search results may include multiple matches for an album. //// ENTER Press ENTER to obtain title information. ENTER To obtain title information to an individual track or multiple tracks You can obtain title information to an individual track or to multiple tracks in a single operation. [. . . ]