User manual SONY CLIE PEGA-BP500

[. . . ] Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. This caution label is located inside the unit. Welcome! Thank you for purchasing the Sony Flat Component System. [. . . ] 1 Combining 4 A#1 B C #1 and #3 are combined. 1 3 2 C A(#1+#3) B 2 #3 3 TRACK MD The total number of tracks on the MD increases by one and all tracks following the divided track are renumbered. Example: Dividing track 2 to create a new track for C Track 1 2 3 number A B C D Dividing 1 23 4 A B C D Track 2 is divided, creating a separate track for C, and all the following tracks are renumbered. 4, 6 1 Press MD. 2, 5 , , The unit enters MD play mode. 2 2 Turn the JOG dial until the track number you want to move appears in the display. For example, if you want to move 7th track to 1st, turn the JOG dial until 7th track appears in the display. 12345 6 7 8 9 10 11 VOLUME POWER m ON Erasing 2, 4 Track number you want to move Music calendar 3 Press EDIT/NO repeatedly until "Move ?" appears in the display. 3, 6 1 5 , , Moving Recorded Tracks (move function) You can change the position of any track. After you move a track, the tracks between the new and old track positions are automatically renumbered. 4 Press ENTER/YES. 5 Turn the JOG dial until the new track number appears. TOC EDIT MD 1 While playing the MD, press fl at the point where you want to create a new track. The deck pauses playing. 12345 6 7 8 9 10 11 VOLUME New track number Track number you want to move 2 Press EDIT/NO repeatedly until "Divide ?" appears in the display. 3 Press ENTER/YES. "Rehearsal" alternates with "Position ok?" in the display, and the starting portion of the new track begins playing repeatedly. 6 Press ENTER/YES. After you have moved the track, "Complete" appears for a few seconds. To stop before the track has been moved Press . continue to next page m Chapter 5: Editing Recorded MDs 19 m continued Example: Combining B and C Track number Combining 12345 6 7 8 9 10 11 VOLUME If "Sorry" appears in the display 4 If the starting position is incorrect, press EDIT/NO. If it is correct, go to step 6. TOC EDIT TRACK MD 1 A 1 A 23 B C 2 B 4 D 3 The tracks cannot be combined. This sometimes happens when you have edited the same track many times. This is due to a technical limitation of the MD system, not a mechanical error. C D Playing track number flashes B and C are combined into one track. The cursor shifts rightward and stands by for the input of the next character. 12345 6 7 8 9 10 11 VOLUME DISC MD Next character 8 Repeat steps 5 and 7 until you have entered the entire title. If you want to enter the same type of character, skip step 5. If you entered the wrong character Press ) or 0 until the character to be corrected starts flashing, and repeat steps 5 to 7 to enter the correct character. To erase a character Press ) or 0 until the character to be erased starts flashing, then press EDIT/NO. 9 Press ENTER/YES. This completes the labelling procedure and the title scrolls in the display. To stop before the track has been labelled Press . To check the titles You can check the disc or track name by pressing SCROLL. To check the Press SCROLL* Disc name Track name While the deck is stopped While the deck is playing * Press SCROLL again to pause, and once more to continue scrolling. Chapter 5: Editing Recorded MDs 21 Chapter 6: the Radio Listening to the Radio Presetting Radio Stations Playing Preset Radio Stations Listening to the Radio You can have the tuner automatically scan and tune in the stations with clear signals. This feature saves you time in searching for stations with clear signals. However, you will have to manually tune in the stations with weak signals that are skipped by automatic tuning. POWER m ON "TUNED" appears in the display. "STEREO" also appears if the tuned FM station is broadcasting in stereo. > ­ Scans a lower frequency station Scans a higher frequency station AUTO VOLUME 4 If you do not want to listen to the station 1 selected, turn the JOG dial again to restart the scan. When the desired station is not tuned in Automatic tuning may skip stations with a weak signals. 1 Press TUNING repeatedly until "MANUAL" appears in the display. 2 Keep turning the JOG dial until the desired station is tuned in. 2 STEREO/ MONO 3, 4 1 Press TUNER/BAND (or BAND on the remote) repeatedly until the band you want appears in the display. [. . . ] m Check the speaker connection and speaker placement. m TV or VCR is too close to the stereo system. Move the stereo system away from the TV or VCR. "0:00" flashes in the display. [. . . ]