User manual SONY CLIE PEGA-KB100 KEY LAYOUT

[. . . ] This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. This caution label is located inside the unit. Note The AC power cord has been fixed on the rear panel with the plug band temporarily for shipment. Unlock the plug band to remove the plug. Back panel Plug band This stereo system is equipped with the Dolby* Btype noise reduction system. [. . . ] After the last track, "END" appears. Press CHECK until the track or disc you do not want appears, then press CLEAR. 4 To programme a whole disc, skip this step. Press /± until the desired track number appears. When the disc you select has a disc title, it appears and then switches to the following display. Clear from the Press CLEAR. Each time you last track or disc press the button, the last track or disc will be cleared. Add tracks or discs to the end of the programme Clear a specific programme Follow the programming procedure. 20 ALL 1 DISC S PROGRAM CD TEXT AUTO TUNED STEREO MONO SYNC 1 2 REC SLEEP 20 3 1 STEP VOLUME PLUS 1 RELAY Track number 5 Press ENTER. The track is programmed. The programmed track 1 Press PROGRAM repeatedly until the programme number you want to clear appears. 2 Hold down CLEAR until "ALL CLEAR" appears. 20 ALL 1 DISC S PROGRAM CD TEXT AUTO TUNED STEREO MONO SYNC 1 2 REC SLEEP 20 3 1 STEP VOLUME PLUS 1 Tips RELAY The programmed disc Playing order 6 To programme other discs/tracks, do the following: Repeat Steps 3 and 5 4 and 5 3 to 5 · When you press CD fl, you can play the same programme again. · If you replace discs, the programmed disc and track numbers remain until you erase them. So, the player plays only the existing disc and track numbers. However, the disc and track numbers that are not found in the player or on the disc are deleted from the programme, and the rest of the programme is played in the programmed order. To programme Other discs Other tracks on the same disc Other tracks on other discs 7 Press CD fl. All the tracks play in the order you selected. To cancel Programme Play Press CONTINUE. 24 Playing your favorite CD independently -- Plus One Play When you insert a disc into the PLUS ONE slot, you can play the disc independently from other discs. When using this function, the player is automatically set to 1 DISC Continuous Play mode. The PLUS ONE slot comes to the loading position. 9 41 46 47 48 4 3 49 50 PLUS ONE 1 2 PLUS ONE slot 1 2 3 4 Insert a disc into the PLUS ONE slot. Close the front cover. The player starts playing the disc in the PLUS ONE slot. Note that you cannot change the disc title of the CD-TEXT disc. · You can label discs while the front cover is open. 20 ALL 1 DISC S PROGRAM CD TEXT AUTO TUNED STEREO MONO SYNC 1 2 REC SLEEP S VOLUME PLUS 1 RELAY 5 Press ± to select the character. The cursor shifts rightward and waits for the input of the next character. 20 ALL 1 DISC S PROGRAM CD TEXT TITLE AUTO TUNED STEREO MONO SYNC 1 2 REC SLEEP VOLUME PLUS 1 RELAY If you have made a mistake Press LOOP/DELETE. The character 1 space before the cursor disappears and the cursor flashes. Input the correct characters. 6 7 Repeat Steps 4 and 5 to input more characters. Press ENTER to complete the labelling procedure. The disc name lights up in the display. 20 ALL 1 DISC S PROGRAM CD TEXT TITLE AUTO TUNED STEREO MONO SYNC 1 2 REC SLEEP SONYHITS VOLUME PLUS 1 RELAY Repeat Steps 2 to 7 to label other discs. 27 Locating a specific CD FUNCTION /± Note If "NO ENTRY" appears, no disc has been labeled. Try the Memo Scan function again after labeling the discs. Locating a disc by searching a specific disc title -- Memo Search You can search and locate a disc you want by inputting the first character used in the disc title (see page 26). 1 2 Press FUNCTION repeatedly until "CD" appears. Press MEMO SEARCH ( or SEARCH on the remote). "MEMO SEARCH" appears and the lamp on the ENTER button flashes. ENTER jog dial MEMO MEMO SCAN SEARCH 3 Press /± repeatedly to input the first character. Locating a disc by scanning each disc title -- Memo Scan You can locate a disc you want to play quickly by scanning the disc title (see page 26) in the display and start playing. Note that you cannot use this function in the ALL DISCS Shuffle Play mode. 20 ALL 1 DISC S PROGRAM CD TEXT TITLE AUTO TUNED STEREO MONO SYNC 1 2 REC SLEEP SONYHITS VOLUME PLUS 1 RELAY Each time you press /±, the characters appear in the following order. ABCDEFGHIJKLMNOPQRST UVWXYZ0123456789 If "[A] NOT FOUND" appears in the display while inputting the first character with the /± buttons, no disc has been labeled using the input character. Notes · When searching input characters, blanks and symbols before the first character in the Disc Memo are ignored. · When searching input characters, upper and lower cases cannot be differentiated. 1 2 Press FUNCTION repeatedly until "CD" appears. [. . . ] Leave the system turned on for about an hour until the moisture evaporates. Play does not start from the first track. ·The player is in programme or shuffle mode. ·You have reached the end of the CD. [. . . ]