User manual SONY PEGA-KB11

[. . . ] This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including any interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] · All other trademarks are trademarks of their respective owners. Reproduction in whole or in part without written permission is prohibited. You can now fold up the keyboard. Unfold the keyboard and set it on a firm, flat surface. 4 Fold the keyboard as shown. Press the four corners of the case together until they click into place to close the keyboard. 2 Slide the end grips inward, bringing the keyboard sections together. 4 After setting, tap the home screen. End grip icon to return to the v End grip Using the keyboard again Note When you disconnect your CLIÉ handheld, make sure to pull it straight upward. If you pull your CLIÉ handheld toward you with too much force, the PDA foot may be broken and cause a malfunction. Tap the check box of [Enable Keyboard] to tick the item on the General settings screen. For the latest support information, check our official Sony CLIÉ Web site http://www. ita. sel. sony. com/ support/clie/access/ The Keyboard is set. Printed on 100% recycled paper using VOC (Volatile Organic Compound)free vegetable oil based ink. Attaching the Keyboard to your CLIÉ handheld Before attaching the keyboard to your CLIÉ handheld, make sure to tap the check box of [Enable Keyboard] to tick the item on the General settings screen. Attaching the keyboard without the tick on the item, CLIÉ handheld may start a HotSync operation. This is not a malfunction. Assigning Application Shortcut Keys You can assign application shortcuts to the 1 - 9 keys at the top of the keyboard. 3 Tap V to the right of [Tab], and select either setting. To use on-screen button shortcuts, perform one of the following procedures; - Enter the button name while pressing the Fn key. - Enter the first letter of the button name that is not used in the button name, or other one letter while pressing the Ctrl and Cmd keys at the same time. Troubleshooting Nothing happens when you type on the keyboard. - Check that your CLIÉ handheld is charged. - Make sure that your CLIÉ handheld is connected to the keyboard correctly. - Confirm that the application for this keyboard is installed properly. - Confirm that the application for this keyboard is enabled. A HotSync operation cannot be performed when you connect this keyboard to your CLIÉ handheld. - You cannot use this keyboard as a cradle for your CLIÉ handheld. To perform a HotSync operation, remove the keyboard, and attach a cradle to your CLIÉ handheld. HotSync screen appears when you connect this keyboard to your CLIÉ handheld. - The driver may not be installed correctly. Delete the current driver, and install the driver again. If the installed driver is not deleted, operational malfunction may occur. In this case, perform a soft reset following the operation manual of CLIÉ handheld. - The keyboard may not function if you perform a soft reset when the keyboard is connected to your CLIÉ hendheld. Disconnect the keyboard before performing a soft reset on your CLIÉ handheld. Do not connect the keyboard to your CLIÉ handheld while it is starting again. 1 Turn on your CLIÉ handheld, and tap the [Keyboard] icon on the home screen. The most recent settings screen appears. Keys to press Fn + Details Ctl + Cmd + n Ctl + Cmd + l Function Selects Details. [. . . ] Tabs forward through fields. * Tabs backward through fields. * Make sure to set the Caps lock to off when you input the characters other than letters using the on-screen button shortcuts. Using the International Keyboard Settings The Palm OS International keyboard settings are supported by the keyboard software which is preinstalled from the supplied CD-ROM. To input characters using the settings, press the Alt key and the desired character. 1 Turn on your CLIÉ handheld, and tap the [Keyboard] icon on the home screen. The most recent settings screen appears. 2 Tap V in the upper right corner of the General settings screen, and select [Layout]. The Layout settings screen appears. List of calculator functions The following list shows the key combinations for calculator functions. [. . . ]