User manual SONY CLIE PEGA-MSB1

[. . . ] This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. This caution label is located inside the unit. The wire which is coloured blue must be connected to the terminal which is marked with letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. [. . . ] Press · to play the same programme again. · If "--. --" appears instead of the total playing time while programming, this means: ­ you have programmed a track numbered over 20, or ­ the total playing time has exceeded 100 minutes. 2 1 2 3 3 Press FUNCTION repeatedly until "CD" appears in the display. Press NON-STOP so the indicator on this button lights up. Press ·. To cancel Non-Stop Play Press NON-STOP so the indicator on this button goes off. 25 The Tape Deck Recording on a tape manually You can record from CDs, tapes, or the radio as you like. For example, you can record just the songs you want or begin recording from the middle of the tape. The recording level is adjusted automatically. 5 6 Press P on deck B. Recording starts. Start playing the source to be recorded. To Stop recording Pause recording Press p on deck B P on deck B 2 Tips · If you want to record on the reverse side, press ª so the indicator on the ª button (for the reverse side) lights up green. · When you want to reduce the hiss noise in lowlevel high-frequency signals, press DOLBY NR before step 5 so "DOLBY NR B" appears in the display. 4 DOLBY NR 1 2 3 ª p 5 13 Insert a blank tape into deck B. Press FUNCTION repeatedly until the source you want to record (e. g. , CD) appears in the display. Press r REC. Deck B stands by for recording, and the indicator on the · button (for the front side) lights up green. 4 Press DIRECTION repeatedly to select A to record on one side or ß (or RELAY) to record on both sides. 26 Recording CDs by specifying the track order -- Programme Edit You can record tracks from all the CDs in the order you want. When programming, make sure the playing times for each side do not exceed the length of one side of the tape. 1 2 3 4 5 6 Place CDs and close the front cover. Press FUNCTION repeatedly until "CD" appears in the display. The personal file function (see "Making a personal audio emphasis file (Personal File)") lets you store your own effects. SPECTRUM ANALYZER EFFECT To cancel the audio emphasis Press EFFECT (or MUSIC MENU ON/OFF on the remote) repeatedly so the indicator on the EFFECT button goes off. Music menu options "SUR " appears if you select an audio emphasis with a surround effect. Press GEQ V/v GEQ B/b To select MENU 1 ROCK POP JAZZ DANCE SALSA MENU 2 MOVIE GAME NIGHT PARTY RELAX 1, 2 To change the equalizer display Each time you press SPECTRUM ANALYZER, the equalizer display changes to show one of the four displays below. 1 Press GEQ V/v (or MUSIC MENU V/v on the remote) repeatedly to select MENU 1 or MENU 2. See the chart "Music menu options" below. The last audio emphasis chosen from that menu appears in the display. 63 250 1K 4K 16K(Hz) 2 Press GEQ B/b (or MUSIC MENU B/b on the remote) repeatedly to select the audio emphasis you desire. The audio emphasis name appears in the display. 32 Adjusting the audio emphasis You can adjust the audio emphasis using the graphic equalizer and surround effect. 4 Press GEQ V/v to adjust the level. DOLBY NR OFF ALL DISC S 63 250 1K 4K 16K(Hz) 6 2 3, 4 5 6 Repeat steps 3 and 4 to adjust the other frequency bands. Press ENTER when finished. Note If you choose another audio emphasis (other than "EFFECT OFF"), the adjusted sound effect is lost. To retain the adjusted sound effect for future use, store it in a personal file (see "Making a personal audio emphasis file"). Adjusting the graphic equalizer You can adjust the sound by raising or lowering the levels of specific frequency ranges. Before operation, first select the basic audio emphasis you want for your sound. 1 2 3 Select the basic audio emphasis you want for your sound. (see "Selecting the audio emphasis. ") Press GEQ CONTROL. The frequency range appears and the level value flashes in the display. Press GEQ B/b repeatedly to select a frequency band. DOLBY NR OFF ALL DISC S 63 250 1K 4K 16K(Hz) continued 33 Adjusting the Audio Emphasis (continued) Adjusting the DSP level Activating the Surround effect The Surround Menu lets you select the sound characteristics according to the sound you are listening to. DSP DSP LEVEL / Press DSP LEVEL on the remote to select the DSP level. Each time you press this button, the level changes as follows: LEVEL 1 n 2 n 3 n / Press DSP (or DSP MODE on the remote) until the desired DSP mode appears in the display. Each time you press this button, the menu changes as follows: DSP OFF: Deactivates the DSP mode HALL: Reproduces the acoustics of a concert hall THEATER: Reproduces the acoustics of a movie theatre Notes · If you choose other sound effects, the surround effect will be cancelled. To retain the effect, store it in a personal file (see "Making a personal audio emphasis file"). · You can adjust the DSP level when the DSP mode is activated. 34 Making a personal audio emphasis file -- Personal File You can create personal files of audio patterns (surround effect and graphic equalizer) and store them in the unit's memory. Later call up an audio pattern to play a favourite tape, CD, or radio programme. Before operation, first select the basic audio emphasis you want for your sound. 4 Press ENTER. The adjusted sound effects are stored under the selected file number. Any settings previously stored at this memory location are erased and replaced by the new settings. To call up the personal file 1 Press GEQ V/v (or MUSIC MENU V/v on the remote) repeatedly to display the last selected personal file. 2 Press GEQ B/b (or MUSIC MENU B/b on the remote) repeatedly to select the desired personal file. 42 3 1 Create the sound effect you want by using the graphic equalizer and surround effect (see "Adjusting the audio emphasis"). [. . . ] ·The player is in Programme or Shuffle Play mode. Press PLAY MODE repeatedly until "PROGRAM" or "SHUFFLE" disappear from the display. Tuner Severe hum or noise ("TUNED" or "STEREO" flashes in the display. ·The signal strength is too weak. A stereo FM programme cannot be received in stereo. [. . . ]