User manual SONY PEG-AWL100

[. . . ] 4-668-080-11 (1) Wireless LAN Card Operating Instructions PEGA-WL100 2002 Sony Corporation Owner's Record The model number and serial number are located at the rear of the product. Record the model number and the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model Number : PEGA-WL100 Serial Number : __________________ For the customers in USA and Canada : NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] · Depending on the manufacturer, the above WEP keys may be assigned a different name. 11 Tap [OK]. The basic settings are completed by the profile name you set in Step 7. 12 Tap the Home icon on your CLIÉ handheld. The home screen appears. 18 Modifying the settings 1 Tap the [Prefs] icon on the home screen of your CLIÉ handheld. 2 Tap V in the upper right corner of the screen, and select [Network]. 3 Tap V of [Service], and select [Wireless LAN]. 4 Tap [Details. . . ] in the lower left corner of the screen. The [Wireless LAN Setup] screen appears. 5 Tap V below [ProfileName], and select the profile name you want to modify. 6 Tap [Edit] at the bottom of the screen. The [Wireless LAN Setup] input screen appears. The home screen appears. Deleting the profile you have set 1 In Step 6 of "Modifying the settings" above, tap [Delete] at the bottom of the screen. Note Do not modify the settings while the Wireless LAN card is being connected to the wireless LAN access point. 19 Advanced Settings Setting a network manually When it is necessary to set a network IP address or DNS address, follow the procedure below. 1 2 Tap [Advanced Setup] in the lower right corner of the [Wireless LAN Setup] input screen. Tap the checkbox of [Auto] in [IP Address] or [DNS Address], and remove the tick. The IP Address input screen or the DNS Address input screen appears. 3 4 Enter necessary addresses. Tap [OK] when you complete the setting. Disabling the power saving mode 1 Tap [Advanced Setup] in the lower right corner of the [Wireless LAN Setup] input screen. 2 Tap the checkbox of [Enable] in [PowerSaveMode], and remove the tick. Tip When the communication conditions are not good, you can disable the power saving mode to maximize the battery power and achieve better communications. However, it will make the battery life shorter. Normally, the power saving mode is recommended. 20 Connecting your CLIÉ Handheld to a Wireless LAN 1 2 Insert the Wireless LAN card in Wireless Communication Slot of your CLIÉ handheld. Tap the [Prefs] icon on the home screen of your CLIÉ handheld. The [Preferences] screen appears. 3 Tap V in the upper right corner of the screen, and select [Network]. The [Network] screen appears. 4 Tap V of [Service], and select [Wireless LAN]. Tip If you have set only one profile, go to Step 8. Continued on next page 21 5 Tap [Details. . . ] in the lower left corner of the screen. The [Wireless LAN Setup] screen appears. 6 Tap V below [Profile Name], and select the profile name you want to use. 7 8 Tap [OK]. The [Preferences] screen appears again. Tap [Connect] at the bottom of the screen. Your CLIÉ handheld begins to connect to a wireless LAN. When a connection is established, start up the application you like. 22 Performing Communications Directly between your CLIÉ Handheld and Another Device on a Wireless LAN (Ad-Hoc Mode) Your CLIÉ handheld can communicate directly with another device on a wireless LAN without using a wireless LAN access point. The Ad-hoc mode settings and communications require network knowledge. Basic Settings 1 2 3 4 Insert the Wireless LAN card in Wireless Communication Slot of your CLIÉ handheld. Tap the [Prefs] icon on the home screen of your CLIÉ handheld. The [Preferences] screen appears. Tap V in the upper right corner of the screen, and select [Network]. The [Network] screen appears. Tap V of [Service], and select [Wireless LAN]. Continued on next page 23 5 Tap [Details. . . ] in the lower left corner of the screen. The [Wireless LAN Setup] screen appears. 6 Tap [Create]. A new input screen of [Wireless LAN Setup] appears. Tip Tapping the mark in the upper right corner of the screen shows a brief explanation for the setting. 7 Enter a profile name in [ProfileName]. Specify a name freely according to the name of the other communication device, access point, etc. 24 8 Enter a network ID in [NetworkID (SSID)]. Specify an alphanumeric string freely. The same network ID (SSID) needs to be entered in both your CLIÉ handheld and the other communication device. 9 Select the encryption level in [WEP]. Be sure to select the same encryption level for both your CLIÉ handheld and the other communication device. Tip When you select [None] in [WEP], you do not need to enter a WEP key. In this case, skip the next step, and go to Step 11. Continued on next page 25 10 Enter a WEP key. Be sure to enter the same WEP key in both your CLIÉ handheld and the other communication device. For details on WEP key, see pages 17-18. b 11 Tap [Adhoc] in [ConnectMode]. The Ad-hoc mode is selected as the connection type. 26 12 Tap V of [ch] below [Adhoc], and select a channel. Be sure to select the same channel for both your CLIÉ handheld and the other communication device. [. . . ] Be careful of the remaining battery power). · There is a device operating at the 2. 4 GHz band of frequencies (microwave oven, Bluetooth-enabled device, etc. ) around the CLIÉ handheld. p Increase the distance between the device and the CLIÉ handheld or turn off the power of the device. You forget a WEP (encryption) key. p After changing all the settings of the access point to its factory default setting, set the access point again. To restore the default settings, see the operating instructions of the access point. [. . . ]