User manual SONY PHC-Z10

[. . . ] 3-048-920-11 (1) Personal Component System Operating Instructions PHC-Z10 ©2000 Sony Corporation Warning To prevent fire or shock hazard, do not expose the player to rain or moisture. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. [. . . ] 1 Turn MULTI JOG to set the hour and press ENTER MEM. 2 Turn MULTI JOG to set the minutes. 3 Press ENTER MEM. The clock starts from 00 seconds. 24 The Timer Waking up to music You can wake up to music or a radio program at a preset time. Make sure you have set the clock ("Setting the clock" on page 24). STANDBY TIMER ENTER MEM MULTI JOG The Timer Note You cannot preset waking up timer and recording timer (page 27) at the same time. Before you begin, make sure the (clock) indication is not lit in the display. If it is lit, press STANDBY. 1 Prepare the music source you want to play. Source CD RADIO TAPE LINE Do this Insert a CD. Turn on the equipment connected to LINE IN. 2 Press TIMER to display the indication. Do the following operations by checking the display. 3 Turn MULTI JOG until the music source you want to play ("CD", "TAPE", "RADIO" or "LINE") appears in the display, and press ENTER MEM. continued The Timer 25 Waking up to music (continued) 4 Set the timer to the hour and the minutes you want the music to start. 1 Turn MULTI JOG to set the hour and press ENTER MEM. 2 Turn MULTI JOG to set the minutes, and press ENTER MEM. 5 6 Set the timer to the hour and the minutes you want the music to go off. (Do as step 4. ) Turn MULTI JOG to set the volume you want, and press ENTER MEM. Tips · To exit the standby mode, press STANDBY to make the indication disappear. · The preset settings remain until you reset them. 7 Press STANDBY. The indication lights up and the power goes off; the player enters the standby mode. At the preset time, the power will go on and music will fade in. Then music will fade out and the power will go off at the preset time, and the player will enter the standby mode again. To check/change the waking up timer settings Press TIMER, then ENTER MEM. Each time you press ENTER MEM, a stored setting is displayed in the set order. To change the setting, display the setting you want to change and re-enter it. To use the player before a timer playback starts If you turn on the player, you can use it as usual ( in case of the radio, if you listen to the station which is different from the one you tuned in step 1 on page 25, you will hear that station at the preset time. ) Turn off the player before the preset time. To stop play Press POWER to turn off the power. 26 The Timer Timer-recording radio programs You can set timer to record the radio at a certain time. You can also record the sound of the component connected to the LINE IN jacks of the player. Make sure you have set the clock (see "Setting the clock" on page 24). STANDBY TIMER ENTER MEM The Timer Notes · You cannot preset recording timer and waking up timer (page 25) at the same time. · When recording from the component connected to the LINE IN jacks of the player, refer to the operating instructions of the component. Before you begin, make sure the (clock) indication is not lit in the display. If it is lit, press STANDBY. 1 2 Tune in the radio station and insert a blank tape into the tape compartment with the side you want to record on facing you. Do the following operations by checking the display window. Tip When you receive the AM program in step 1, press z/X to check if the noise is heard. If so, press MODE to select the position that most decreases the noise. 3 Turn MULTI JOG to display "RADIO" and "REC", and press ENTER MEM. [. . . ] · If you are listening to an FM program near the TV with an indoor antenna, move the player away from the TV. continued "NO DISC" lights in the display even when a CD is in place. The CD does not play. Radio CD Player The picture of your TV becomes unstable. Additional Information 39 Troubleshooting (continued) Symptom The tape does not move when you press an operation button. Remedy · Close the cassette compartment securely. The z/X button does not function/ · Make sure the safety tab on the cassette is in The tape does not play. · Make sure "TAPE" appears in the display window. Tape Player The tape does not erase completely. · Clean the erase head (see page 41). · The source which was recorded on TYPE II (high position) or TYPE IV (metal) tape using this unit is being played. [. . . ]