User manual SONY PMPK-DJ9000

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Precautions On safety · Before operating the unit, check that the operating voltage of your unit is identical with that of your local power supply. [. . . ] Move the tonearm to the desired point on the record. Set the cueing lever to the down position. The tonearm will descend slowly to the record and play will begin. If you want to change the pitch, press the QUARTZ lock button (the QUARTZ indicator will turn off). Then adjust the pitch by moving the PITCH ADJ. The distance from the center position to the farthest point on the scale represents a change of 10% in the pitch. You can also use the PITCH BEND + and ­ buttons to change the pitch (see "Using the PITCH BEND + and ­ buttons" on page 8). If you wish, you can return to normal speed (33 1/3 or 45 rpm) while the PITCH ADJ. knob is off center by pressing the QUARTZ lock button (the QUARTZ indicator will turn on). Press the QUARTZ lock button again to go back to the previous pitch setting (the QUARTZ indicator will turn off). knob does not function while the QUARTZ lock is on (i. e. , while the QUARTZ indicator is on). 2 1 3 5 4 7 8 Before playing a record, be sure the PHONO/LINE switch on the mixer is set to PHONO. 1 Place a record on the platter. 9 Note Place only one record on the platter at a time. Grasp the stylus holder and pull it away from the body of the cartridge. Stylus holder 4 5 Insert the new stylus by pushing it into the cartridge receptacle until it is firmly attached. Should any problem persist after taking the specified remedial actions, consult your nearest Sony dealer. The tonearm skips, skates or fails to advance. b The turntable is not level. Follow the instructions on page 6 and set the tracking force to the appropriate value for the cartridge being used. (The supplied cartridge requires 4 grams of tracking force. ) b The anti-skating adjustment is incorrect. Make sure the ANTI-SKATING dial is set to the value indicated on the tracking force ring (see page 6). Clean the record with a commercially available record cleaning kit, or replace the record. 2 Slide the cartridge backward or forward until the distance between the stylus and the spindle is 15 mm (3/4 inches). Spindle 15 mm (3/4 inches) Make sure to retighten the screws after completing the adjustment. Poor sound quality, excessive noise, intermittent sound, etc. . . b Inspect the locking ring on the tonearm and verify that the headshell is firmly secured (see page 4). b Make sure the ground wire is connected to U (ground) terminal on the mixer (see page 5). Follow the instructions on page 6 to set the tracking force to the appropriate value for the cartridge being used. (The supplied cartridge requires 4 grams of tracking force. ) b The stylus is dirty or worn. Remove dust on the stylus with a stylus-cleaning brush, or replace the worn stylus (see page 9). [. . . ] and Mexico: 120 V AC, 60 Hz European countries: 220 - 230 V AC, 50/60 Hz Other countries: 110 - 120 V/ 220 - 240 V AC, 50/60 Hz 15 W Approx. 450 × 152 × 352 mm (17 11/16 × 5 11/16 × 13 3/4 in) (w/h/d) 10 kg (22 lbs) Supplied Accessories Platter (2) Slip mat (2) Dust cover (with hinges) (2) Counterweight (2) Cartridge and headshell (2) 45 adaptor (2) Audio cord (with ground wire) (2) AC power cord (2) 11 Additional Information Parts and Controls PS-DJ9000 Stereo Turntable System L A B C D E F G H I J K M N O P Q R S T U V W X Y Z wj 1 2 3 4 5 6 7 POWER ON/OFF switch Spindle Strobo lamp START/STOP button Slip mat Platter TARGET LIGHT and release button The TARGET LIGHT allows you to see the position of the stylus in the dark. Push and depress the TARGET LIGHT to turn it off. Push the release button to raise the light again and turn it on. [. . . ]