User manual SONY PRS-T2WC

[. . . ] As the S-AIR product uses the radio waves that share the same frequency as other wireless systems, such as wireless LAN or Bluetooth devices, interference or poor transmission may result. In this case, take the following steps: Do not install the S-AIR product near other wireless systems. Do not use the S-AIR product and the other wireless systems at the same time. The transmission distance differs depending on the usage environment. [. . . ] Do not insert any device other than the supplied wireless transceiver (EZW-RT10) into the EZW-RT10 slot. Heat buildup on the unit during operation is normal and is not cause for alarm. Do not touch the cabinet if it has been used continuously at a high volume because the cabinet may have become hot. Do not obstruct the ventilation holes. On the speaker system function. For details on turning on the S-AIR function, refer to the Operating Instructions supplied with the S-AIR main unit. Once the connection is established, the S-AIR indicator on the front of the unit lights up and "LINKED" appears in the display for about 2 seconds. S-AIR (Sony Audio Interactive Radio frequency) Notice for the customers in the U. S. A. This speaker system is not magnetically shielded, and the picture on nearby TV sets may become magnetically distorted. In this situation, turn off the TV, wait about 15 to 30 minutes, and turn it back on. If there is no improvement, move the unit far away from the TV. If you cannot connect to the S-AIR main unit The following indications are located on the bottom exterior. Cleaning the cabinet Clean this unit with a soft dry cloth. Do not use any type of abrasive pad, scouring powder, or solvent, such as thinner, benzine, or alcohol. It is easy to set the same S-AIR ID for the unit and SAIR main unit to establish the connection. However, if a neighbor has an S-AIR main unit with the same S-AIR ID as your S-AIR main unit, you may be able to hear the audio transmitted from your neighbor's S-AIR main unit on your system. To prevent this, you can identify the unit with a specific S-AIR main unit by performing the pairing operation. When you perform pairing Recent times have seen the rapid spread of DVD media, Digital Broadcasting, and other high-quality media. To ensure that the subtle nuances of these highquality media are transmitted with no deterioration, Sony has developed a technology called "S-AIR" for the radio transmission of digital audio signals with no compression, and has incorporated this technology into the EZW-RT10. UNLINKED: Displayed when the connection with the S-AIR main unit is cut off. Specifications Amplifier section U. S. A. model: AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 3 ohm loads, both channels driven, from 300 20, 000Hz; rated 4 watts per channel minimum RMS power, with no more than 10% total harmonic distortion from 250 milliwatts to rated output. Other models: Continuous RMS power output (reference): 4 + 4 W (3 ohms at 1 kHz, 10% THD) 2 Find your problem in the checklist below, and take the indicated corrective action. If the issue persists, contact your nearest Sony dealer. When bringing this unit in for repairs, be sure to bring in the entire system (this unit, the S-AIR main unit, and wireless transceivers). This product is a system product, and the entire system is needed to determine the location requiring repair. If the STANDBY indicator flashes Output Immediately unplug the power cord, and check the following item. Is anything blocking the ventilation holes on the rear of the unit?Use the same procedure to set the minute. The clock settings are lost when you disconnect the power cord or if a power failure occurs. Information of the connected S-AIR main unit1) Model name of the connected S-AIR main unit2) Clock2)3) . . . When the unit is not connected to an S-AIR main unit: "S-AIR" "UNLINKED"2) Clock2)3) . . . If you use another S-AIR main unit, place it more than 8 m (26 1/4 feet) away from the S-AIR main unit you are using. Confirm the S-AIR IDs of the unit and the S-AIR main unit. The unit is paired with another S-AIR main unit. [. . . ] Confirm the S-AIR IDs of the unit and the S-AIR main unit. Place so that the unit and the S-AIR main unit are closer. Stop using any equipment that generates electromagnetic energy such as a microwave oven. Place so that the unit and the S-AIR main unit are separated from other wireless devices. [. . . ]