User manual SONY PS-LX520

[. . . ] Refer servicing to qualified personnel only. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] · To switch to the tape while listening to another source, press TAPE nN on the remote while the tape is stopped. The tape will automatically start playing (Automatic Source Selection). · To play a tape recorded with the Dolby NR system, press DOLBY NR on the remote before step 4. ";" appears. Basic Operations 2 3 Press FUNCTION repeatedly until "TAPE" appears. Press DIR MODE on the remote to select "g" to play one side of the tape or "j"* to play both sides repeatedly. * The tape automatically stops after playing back five times. 4 Press N. To start playing the reverse side, press n. The tape starts playing. To Stop playback Pause Do this Press x. With the tape stopped, press . m/M> (or j/J on the remote). Fast-forward or rewind Locate the begining During playback, press of the current or next . m/M> (or track l/L on the remote). Remove or replace the tape Adjust the volume Press Z PUSH. Press VOLUME +/­. 19 The CD Player Checking the remaining playing time on the CD Do the procedure below to check the remaining playing time of the current track or the entire CD. Playing CD tracks repeatedly -- Repeat Play The Repeat Play function lets you playback a single track or all the tracks on a CD repeatedly in Normal Play. You can also use Repeat Play function while in Shuffle Play or Program Play. DISPLAY CD REPEAT , Press DISPLAY. Each time you press this button, the display changes as follows: During playback t Current track number and elapsed playing time of the track r Current track number and remaining playing time of the track r Remaining playing time of the entire CD , Press CD REPEAT repeatedly during playback until "REPEAT" appears. Repeat Play starts. The following table describes the two repeat modes. To repeat All the tracks on the CD Only the currently playing track* Press CD REPEAT repeatedly until "REPEAT" appears. Press l or L repeatedly until the desired track number appears. 1 A 3 + ­ ?/1 3 243 Total playing time Selected track number n x N . m X M> Z 6 7 Press ENTER. Repeat steps 5 and 6 to add more tracks to be recorded on side A. Press S where you want the system to begin recording on side B. Repeat steps 5 and 6 to select tracks to be recorded on side B. 2 8 9 8, 12 11 4 6 s 5 10 DOLBY NR 24 10 Press z REC. The tape stands by for recording and the CD stands by for playback. "SYNCHRO" and "REC" appear. 11 Press DIR MODE to select "g" to record on one side of the tape or "j" to record on both sides. 12 Press S. Recording starts on the side of the tape facing towards you. The Tape Deck To stop recording Press s. To cancel Program Edit Press PLAY MODE repeatedly until "PROGRAM" disappears. Tip To record with the Dolby NR system on, press DOLBY NR on the remote before step 12. ";" appears. 25 Sound Adjustment Generating a more dynamic sound The Dynamic Sound Generator (DSG) automatically enhances your music to produce a more powerful sound. Selecting the sound mode You can enjoy simulated surround stereo effects when you listen to the music near the unit. SURROUND DSG , Press SURROUND. "SURR" appears. To cancel the Surround Press SURROUND again. 26 Other Features Using the Radio Data System (RDS) (European model only) Falling asleep to music -- Sleep Timer The Sleep Timer function lets you specify a sleep time, after which the system stops playing and turns off automatically. You can thus fall asleep to music. What is the Radio Data System? Radio Data System (RDS)* is a broadcasting service that allows radio stations to send additional information along with the regular program signal. Note RDS may not work properly if the station you have tuned in is not transmitting the RDS signal properly or if the signal is weak. * Not all FM stations provide RDS service, nor do they all provide the same types of services. [. . . ] · The two wires comprising the FM antenna have been pulled further apart since the system was first purchased. A stereo FM program cannot be received in stereo. · Press STEREO/MONO on the remote until "ST" appears in the display. Tape Deck Recording cannot be done. · There is no tape in the cassette holder. [. . . ]