User manual SONY PS-LX55

[. . . ] Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off. Install this system so that the power cord can be unplugged from the wall socket immediately in the event of trouble. Notice for the customers in the U. S. A. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Important Safety Instructions 1) Read these instructions. 5) Do not use this apparatus near water. [. . . ] The Equalizer function is on. 2 Connect the cable with the white plug to the white (L) jack and connect the cable with the red plug to the red (R) jack. Make sure to insert the plugs firmly into the jacks. If the plugs are not inserted firmly, noise may occur. GB Operations Playing a Vinyl Record 3 Set the SIZE SELECTOR to 17 or 30. 4 Turn the protective cover to expose the stylus. 5 Close the dust cover. 6 Press START. Note The platter starts rotating. Lower the volume of the amplifier to prevent damage to it. If the tone arm descends and the stylus touches the vinyl record, a loud creaking noise may occur and harm the amplifier or speakers. Adjust the volume of the amplifier after the stylus descends. 45 r/min adaptor STOP UP/DOWN 1 Place a vinyl record on the platter. 7 Adjust the volume on your amplifier. When playback is finished The tone arm returns to the arm stand automatically, then the platter stops rotating. To stop playing Press the STOP button. The tone arm returns to the arm stand. The platter stops rotating. Note Place only one vinyl record on the platter at a time. If two or more vinyl records are stacked on the platter, the stylus will not make proper contact with the grooves and the quality of reproduction will be impaired. 2 Press the Speed select button to select the speed. GB To pause playing Press the UP/DOWN button to raise the stylus off the vinyl record. To play a different part of the vinyl record 1 After performing step 4, press the UP/ DOWN button, then lift the tone arm. desire. Recording Audio Tracks on Your Computer You can record audio tracks of a vinyl record on your computer by: · Connecting the turntable and your computer using the supplied USB cable · Using the supplied software, "Sound Forge Audio Studio LE" 2 Move the tone arm to the position you 3 Press the UP/DOWN button. The tone arm descends to the record, then playback starts. System requirements for the computer to be connected to the turntable* · Compliant computer: IBM PC/AT or compatible computers · Operating systems: Windows® XP Home Edition Service Pack 2 or higher Windows® XP Professional Service Pack 2 or higher Windows Vista® Home Basic Windows Vista® Home Premium Windows Vista® Business Windows Vista® Ultimate Windows 7 Home Premium Windows 7 Professional Windows 7 Ultimate Pre-installed (manufacturer installed only) Operations To play a 17-cm vinyl record Place the supplied 45 r/min adaptor on the spindle. When you have finished using the adaptor, put it back in the adaptor tray. · Hardware Environment: ­ Operating systems other than those listed above are not supported. ­ Windows XP 64 bit and Windows Vista 64 bit are not supported. For details, refer to your computer's documentation. the [Sounds and Audio Devices Properties] screen. Setting your default playback device using Windows 7 ([Control Panel] is in the [Category] view) 1 Select [Control Panel] from the [Start] menu. 2 Select [Hardware and Sound]. 5 On the [Playback] tab, select your computer's speakers and click the [Set Default]. This device may vary depending on your computer. For details, refer to your computer's documentation. 5 Click [Apply], and then click [OK] to close 6 Click [OK] to close the [Sound] screen. Continued 1GB Setting the default playback device in Sound Forge Audio Studio LE 1 Start the Sound Forge Audio Studio LE software. menu. Recordingaudiotracksfromthe turntableonacomputer For details on recording operations, refer to the supplied document titled "Recording audio tracks of a vinyl record to your computer. " For details about using the software, refer to the "Sound Forge Audio Studio LE" quick start guide (on the supplied CD-ROM) or on-line help of the software. 2 Select [Preferences] from the [Options] 3 Select the [Audio] tab. 4 Select [Microsoft Sound Mapper] from the [Audio device type] drop-down list. the [Preferences] screen. 5 Click [Apply], and then click [OK] to close Reference guides for the supplied software If you still cannot hear audio Check the connection. Exit Sound Forge Audio Studio LE once and then restart the software. Refer to the following instructions: The installation guide for "Sound Forge Audio Studio LE": Refer to this supplied manual to install "Sound Forge Audio Studio LE. " The "Sound Forge Audio Studio LE" tutorial: This tutorial provides easy instructions on how to operate the software. After installing the software, the tutorial appears when you launch the software for the first time. The "Sound Forge Audio Studio LE" quick start guide (on the supplied CD-ROM): This provides instructions on the basic operation of the software. 1GB Additional Information On repacking Keep the carton and packing materials. [. . . ] Make sure the power cord is inserted all the way into an AC wall outlet. Make sure that the drive belt is looped around the motor pulley completely. For details, consult your nearest Sony dealer. The turntable is not connected to the PHONO IN inputs on the amplifier (see page 7). 1 Select [Control Panel] from the [Start] menu. 2 Click [Performance and Maintenance]. [. . . ]