User manual SONY PVM-2530/BS

[. . . ] If shipped to USA/Canada, install only a UL LISTED/CSA LABELLED power supply cord meeting the following specifications: SPECIFICATIONS Plug Type Nema-Plug 5-15p Cord Type SVT or SJT, minimum 3 × 18 AWG Length Maximum 15 feet Rating Minimum 7 A, 125 V WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. Dangerously high voltages are present inside the unit. Refer servicing to qualified personnel only. FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] Each time you press the button, the mode changes as follows. The brightness of the screen will decrease as the mode setting changes from HIGH to LOW. If you select USER, you can adjust the backlight level by pressing the m/M buttons, the same as when you select BACKLIGHT using the menu. : USER 100 2 CONTRAST 6 (page 12) Select the CONTRAST menu to adjust the picture contrast. CONTRAST 100 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T 3 BRIGHTNESS 8 (page 12) Select the BRIGHTNESS menu to adjust the picture brightness (black level). BR I GHTNESS 100 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T Only while the mode is set to USER, are the BACKLIGHT, CONTRAST, and BRIGHTNESS items of the menu available (page 11). If you select LOW, the power consumption is reduced (page 16). 4 SCREEN (page 12) Select the SCREEN menu to adjust the picture's sharpness (phase/pitch) or its centering (horizontal/vertical position). SCREEN AU TO PHASE P I TCH H CENTER V CENTER 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T Navigating the menu Press the MENU button to display the main menu on your screen. See page 11 for more information on using the MENU button. 5 COLOR (page 13) Select the COLOR menu to adjust the color temperature of the picture. While COLOR is set to sRGB, you cannot adjust CONTRAST, BRIGHTNESS or GAMMA. 6 GAMMA (page 14) Select the GAMMA menu to change the picture's color shade setting. COLOR 9300K 6500K s RGB USER AD J U S T 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T MENU , BACKL I GHT GAMMA GAMMA 1 GAMMA 2 GAMMA 3 100 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T Use the m/M and OK buttons to select the icons in the above main menu illustration. Keep pressing m to scroll down until the icons in menu 9 and 0 appear. See page 11 for more information on using the m/M and OK buttons. 7 SHARPNESS (page 14) Select the SHARPNESS menu to adjust to sharpen the edge of images. S H AR P N E S S 5 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T 10 8 MENU POSITION (page 14) Select the MENU POSITION to change the onscreen menu position. 3 Adjust the menu. MENU POS I T I ON Press the m/M buttons to make the adjustment, then press the OK button. When you press the OK button, the setting is stored, then the display returns to the previous menu. 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T OK , 9 LANGUAGE (page 15) Select LANGUAGE to change the language used on menus or messages. L A N G UAG E ENGL I SH FRANÇA I S DEUTSCH ESPA ÑOL I TA L I ANO 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T 4 Close the menu. Press the MENU button once to return to normal viewing. If no buttons are pressed, the menu closes automatically after about 45 seconds. 0 Other menus (page 15) Set the following menu items. If vertical stripes are observed over the entire screen, adjust pitch by the following steps. the screen. 8 Click [END] on the screen to turn off the test pattern. 9 Press the OK button. Return to the SCREEN menu. 9 Press the m/M buttons to select PITCH and press the OK button. The PITCH menu appears on the screen. 10 Press the m/M buttons to select OK button. Return to the menu screen. and press the 10 Press the m/M buttons until the vertical stripes disappear. Adjust so that the vertical stripes disappear. Adjusting the color temperature (COLOR) You can select the color level of the picture's white color field from the default color temperature settings. Also, if necessary, you can fine tune the color temperature. You can set the desired color temperature for each mode of the brightness of screen. GB 11 Click [END] on the screen to turn off the test pattern. 12 Press the OK button. Return to the SCREEN menu. 1 Press the MENU button. The main menu appears on the screen. 2 Press the m/M buttons to select and press the press the OK button. The COLOR menu appears on the screen. (COLOR) and 13 Press the m/M buttons to select OK button. Return to the menu screen. 3 Press the m/M buttons to select the desired color temperature and press the OK button. [. . . ] · Adjust the pitch and phase (page 12). x Problems caused by a computer or other equipment connected, and not caused by the monitor · Set the resolution to 1280 × 1024 on your computer. Picture is ghosting Picture is not centered or sized properly Picture is too small · Eliminate the use of video cable extensions and/or video switch boxes. · Check that all plugs are firmly seated in their sockets. · Adjust the pitch and phase (page 12). [. . . ]