User manual SONY PVM-1344Q

[. . . ] If shipped to USA/Canada, install only a UL LISTED/CSA LABELLED power supply cord meeting the following specifications: SPECIFICATIONS Plug Type Nema-Plug 5-15p Cord Type SVT or SJT, minimum 3 × 18 AWG Length Maximum 15 feet Rating Minimum 7 A, 125 V WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. Dangerously high voltages are present inside the unit. Refer servicing to qualified personnel only. FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] If necessary, use the monitor's controls to adjust the picture. Grasp the lower sides of the LCD panel, then adjust screen tilt. If no picture appears on your screen · Check that the power cord and the video signal cable are properly connected. · If NO INPUT SIGNAL appears on the screen: The computer is in the power saving mode. HIGH t MIDDLE t LOW t USER t HIGH The brightness of the screen will decrease as the mode setting changes from HIGH to LOW. If you select USER, you can adjust the backlight level by pressing the M/m buttons, the same as when you select BACKLIGHT using the menu. : USER 100 2 CONTRAST 6 (page 11) Select the CONTRAST menu to adjust the picture contrast. CONTRAST 100 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T 3 BRIGHTNESS 8 (page 11) Select the BRIGHTNESS menu to adjust the picture brightness (black level). BR I GHTNESS 100 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T Only while the mode is set to USER, are the BACKLIGHT, CONTRAST, and BRIGHTNESS items of the menu available (page 11). If you select LOW, the power consumption is reduced (page 15). 4 SCREEN (page 12) Select the SCREEN menu to adjust the picture's sharpness (phase/pitch) or its centering (horizontal/vertical position). SCREEN AU TO PHASE P I TCH H CENTER V CENTER 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T Navigating the menu Press the MENU button to display the main menu on your screen. See page 11 for more information on using the MENU button. 5 COLOR (page 13) Select the COLOR menu to adjust the color temperature of the picture. This adjusts the tone of the screen. COLOR 9300K 6500K USER AD J U S T 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T MENU , BACKL I GHT 6 GAMMA (page 14) Select the GAMMA menu to change the picture's color shade setting. 100 GAMMA GAMMA 1 GAMMA 2 GAMMA 3 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T Use the M/m and OK buttons to select the icons in the above main menu illustration. Keep pressing m to scroll down until the icons in menu 9 appear. See page 11 for more information on using the M/m and OK buttons. 7 MENU POSITION (page 14) Select the MENU POSITION to change the onscreen menu position. MENU POS I T I ON 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T 10 8 LANGUAGE (page 14) Select LANGUAGE to change the language used on menus or messages. L A N G UAG E ENGL I SH FRANÇA I S DEUTSCH ESPA ÑOL I TA L I ANO 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T x Resetting the adjustments You can reset the adjustments using the RESET menu. See page 14 for more information on resetting the adjustments. Adjusting the backlight (BACKLIGHT) If the screen is too bright, adjust the backlight and make the screen easier to see. Note The backlight cannot be adjusted when the MIDDLE, or LOW (page 10). mode is set to HIGH, 9 Other menus (page 14) Set the following menu items. Return to the menu screen. and press the OK 1 Set the resolution to 1024 × 768 (SDM-HS53) 2 Load the Utility Disk. 1280 × 1024 (SDM-HS73/HS93) on the computer. 12 x Adjust the picture's position manually (H CENTER/V CENTER) If the picture is not in the center of the screen, adjust the picture's centering as follows. Adjusting the color temperature (COLOR) You can select the color level of the picture's white color field from the default color temperature settings. Also, if necessary, you can fine tune the color temperature. 1 Load the Utility Disk. 2 Start the Utility Disk and display the test pattern. For Windows Click [Utility] t [Windows]/[Win Utility. exe]. For Macintosh Click [Utility] t [Mac]/[Mac Utility]. 1 Press the MENU button. The main menu appears on the screen. 2 Press the M/m buttons to select 3 Press the MENU button. The main menu appears on the screen. (COLOR) and press the OK button. The COLOR menu appears on the screen. 3 Press the M/m buttons to select the desired color 4 Press the M/m buttons to select (SCREEN) and press the OK button. Whites will change from a bluish hue to reddish hue as the temperature is lowered from 9300K (default setting) to 6500K. 5 Press the M/m buttons to select H CENTER or V CENTER and press the OK button. The H CENTER or V CENTER menu appears on the screen. Fine tuning the color temperature (USER ADJUSTMENT) USER R G B A D J U S T MENT 120 120 120 6 Press the M/m buttons to center the test pattern in the screen. 7 Click [END] on the screen to turn off the test pattern. 8 Press the OK button. Return to the SCREEN menu. GB 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T 9 Press the M/m buttons to select button. Return to the menu screen. and press the OK 1 Press the M/m buttons to select ADJUST and press the OK button. The USER ADJUSTMENT menu appears on the screen. 2 Press the M/m buttons to select R (Red) or B (Blue) and press the OK button. Then press the M/m buttons to adjust the color temperature and press the OK button. [. . . ] · Adjust the pitch and phase (page 12). x Problems caused by a computer or other equipment connected, and not caused by the monitor · Set the resolution to XGA (1024 × 768) on your computer (SDM-HS53). · Set the resolution to SXGA (1280 × 1024) on your computer (SDM-HS73/HS93). Picture is ghosting Picture is not centered or sized properly Picture is too small · Eliminate the use of video cable extensions and/or video switch boxes. · Check that all plugs are firmly seated in their sockets. [. . . ]