User manual SONY PVM-1390

[. . . ] If shipped to USA/Canada, install only a UL LISTED/CSA LABELLED power supply cord meeting the following specifications: SPECIFICATIONS Plug Type Nema-Plug 5-15p Cord Type SVT or SJT, minimum 3 × 18 AWG Length Maximum 15 feet Rating Minimum 7 A, 125 V WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. Dangerously high voltages are present inside the unit. Refer servicing to qualified personnel only. FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] Keep pressing m to scroll down until the icons in menu 9 to qa appear. See page 11 for more information on using the m/Mm/M and OK buttons. 7 SHARPNESS (page 14) Select the SHARPNESS menu to adjust to sharpen the edge of images. S H AR P N E S S 5 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T 10 8 MENU POSITION (page 14) Select the MENU POSITION to change the onscreen menu position. 3 Adjust the menu. MENU POS I T I ON Press the m/M buttons to make the adjustment, then press the OK button. When you press the OK button, the setting is stored, then the display returns to the previous menu. 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T OK , 9 INPUT SENSING (page 14) Select the INPUT SENSING menu to change the input automatically before the monitor goes into the power saving mode. 0 LANGUAGE (page 15) Select LANGUAGE to change the language used on menus or messages. I NP U T S E N S I NG A U T O ON A U T O OF F 4 Close the menu. 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T L A N G UAG E ENGL I SH FRANÇA I S DEUTSCH ESPA ÑOL I TA L I ANO 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T Press the MENU button once to return to normal viewing. If no buttons are pressed, the menu closes automatically after about 30 seconds. MENU x Resetting the adjustments You can reset the adjustments using the RESET menu. See page 15 for more information on resetting the adjustments. qa Other menus (page 15) Set the following menu items. · RESET 0 · MENU LOCK RESET OK CANCEL Adjusting the backlight (BACKLIGHT) If the screen is too bright, adjust the backlight and make the screen easier to see. Note The backlight cannot be adjusted when the MIDDLE, or LOW (page 10). mode is set to HIGH, GB 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T x Using the MENU, m/M, and OK buttons 1 Display the main menu. Press the MENU button to display the main menu on your screen. 1 Press the MENU button. The main menu appears on the screen. MENU 2 Press the m/M buttons to select (BACKLIGHT) and press the OK button. The BACKLIGHT menu appears on the screen. 3 Press the m/M buttons to adjust the light level and press the OK button. 2 Select the menu you want to adjust. Press the m/M buttons to display the desired menu. Press the OK button to select the menu item. OK , 11 Adjusting the contrast (CONTRAST) Adjust the picture contrast. Note The contrast cannot be adjusted when the MIDDLE, or LOW (page 10). mode is set to HIGH, If the automatic picture quality adjustment function of this monitor seems to not completely adjust the picture You can make further automatic adjustment of the picture quality for the current input signal. Also, if necessary, you can fine tune the color temperature. You can set the desired color temperature for each mode of the brightness of screen. GB 1 Press the MENU button. The main menu appears on the screen. 11 Click [END] on the screen to turn off the test pattern. 12 Press the OK button. Return to the SCREEN menu. 2 Press the m/M buttons to select press the OK button. The COLOR menu appears on the screen. (COLOR) and 13 Press the m/M buttons to select OK button. Return to the menu screen. and press the 3 Press the m/M buttons to select the desired color temperature and press the OK button. Whites will change from a bluish hue to reddish hue as the temperature is lowered from 9300K (default setting) to 6500K. While "User" is selected for the brightness of screen, you can set the color temperature to "sRGB. " When you select "sRGB, " the colors adjust to the sRGB profile. (The sRGB color setting is an industry-standard color space protocol designed for computer products. ) If you select "sRGB, " the color settings of your computer must be set to the sRGB profile. Notes · If a connected computer or other equipment is not sRGB-compliant, color cannot be adjusted to the sRGB profile. · While COLOR is set to sRGB, you cannot adjust CONTRAST, BRIGHTNESS or GAMMA. x Adjust the picture's position manually (H CENTER/V CENTER) If the picture is not in the center of the screen, adjust the picture's centering as follows. 1 Set the resolution to 1280 × 1024 on the computer. 3 Start the CD-ROM, select the region and model, and display the test pattern. For Windows Click [Utility] t [Windows]/[Win Utility. exe]. [. . . ] · Adjust the brightness using the button (page 10). · It takes a few minutes for the display to become bright after turning on the monitor. Picture is dark Wavy or elliptical pattern (moire) is visible Color is not uniform White does not look white Monitor buttons do not operate ( appears on the screen) The monitor turns off after a while · Adjust the pitch and phase (analog RGB signal only) (page 12). · Adjust the pitch and phase (analog RGB signal only) (page 12). · Adjust the color temperature (page 13). [. . . ]