User manual SONY Q004R1

[. . . ] Owner's Record The model and serial numbers are located at the bottom of the projector. Record these numbers in the spaces provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No. Serial No. For customers in the USA If you have any questions about this product, you may contact: Sony Electronics Inc. [. . . ] V: Select to reverse the picture vertically. continued Menu Color Selects the color of the menu display from "Black" or "White. " 48 49 INSTALL SETTING menu (continued) INFORMATION menu Background Selects the background color of the screen when no signal is input. You can select "Black" or "Blue. " Direct Power On Sets the power status of the projector when AC line voltage is supplied. Test Pattern When set to "On, " a test pattern appears on the screen to be used when adjusting the lens with "Focus, " "Zoom" and "Shift, " or correcting the screen proportions with "V Keystone. " A test pattern does not appear when this item is set to "Off. " On: Select to turn the projector on when AC line voltage is supplied. Off: Select to turn the projector to standby mode when AC line voltage is supplied. The INFORMATION menu is used for checking information such as the frequency of the input signal. You can display the settings, but you cannot adjust them. Example: Lamp Timer Displays the total number of hours the projector lamp has been used. DHCP Displays whether the IP address is obtained automatically or not. IP Address Displays the IP address of the projector. High Altitude Mode Off: Select this when using the projector at normal altitudes. On: Select this when using the projector at an altitude of 1, 500 m or higher. Subnet Mask Displays the subnet mask. Adjustments and Settings Using the Menu Lens Control When set to "On, " you can adjust the projection lens using "Focus, " "Zoom" and "Shift. " After you make this adjustment, it is recommended that you set this item to "Off" to avoid any operation of the lens by mistake. Default Gateway Displays the default gateway. fH Displays the horizontal frequency of the input signal. DNS Server Displays the DNS server address. fV Displays the vertical frequency of the input signal. Also, the screen resolution and input signal preset memory No. is displayed. MAC address Displays the MAC address of the projector. 50 51 ImageDirector Features Using ImageDirector, you can adjust the projector's gamma value to your satisfaction from a computer connected to the projector. ImageDirector Ver. 2 enables you to adjust the luminance curve of an input signal differently from the previous version of ImageDirector. The projector can share adjustments with other projectors because ImageDirector Ver. 2. 0 adjusts the curve without changing the preset gamma value on each projector. You can then save this adjusted value to your computer. Refer to the ReadMe. txt and the online help on the supplied CD-ROM for ImageDirector operating instructions. Operating system environment for ImageDirector The ImageDirector application can be used in any of the following operating system environments. Operating systems: Microsoft Windows 98, Windows 98SE, Windows 2000 Professional, Windows Me, Windows XP Home Edition/ Professional CPU: MMX Pentium 166 MHz or more (Pentium II 300 MHz or more recommended) Hard disk: 10 MB or more of free space Memory: 32 MB or more Other hardware requirements: CD-ROM drive If connecting to the projector using a USB jack: USB port (this must be provided as standard), USB cable If connecting to the projector using a COM port: RS-232C serial port, D-sub 9-pin cross (reverse) cable Screen resolution: SVGA (800 × 600 dots) or above, 65536 colors or more Notes · ImageDirector will not work on some computers even though they satisfy the above requirements. · ImageDirector will not work on Macintosh systems. · Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and other countries. · MMX and Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Installing ImageDirector To use ImageDirector, you need to install it on your computer. You need to do this before you use ImageDirector for the first time, or whenever you replace the operating system on your computer. Install ImageDirector as follows. Notes · If you are using Microsoft Windows 2000 Professional, or Windows XP Home Edition/Professional on your computer, log on using the "administrator" account. · If you are using Microsoft Windows 2000 Professional, install ImageDirector on your computer after making sure Microsoft Windows 2000 Service Pack 3 or above is already installed. · If you are using Microsoft Windows XP Home Edition/Professional, install ImageDirector on your computer after making sure Microsoft Windows XP Service Pack 1 or above is already installed. 1 2 3 Insert the ImageDirector CD-ROM in the computer's CD-ROM drive. Installation starts automatically and the setup dialog box opens. Proceed with installation following the messages displayed in the setup dialog box. Notes · During installation, an electronic "End-user License Agreement" is displayed. It is important that you read the agreement first. [. . . ] 49 IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 P, Q PICTURE MODE . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Plug holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19, 61 TRIGGER jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 F Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]