User manual SONY RCP-D50

[. . . ] 3-776-792-12(1) Remote Control Panel Operating Instructions Before operating the unit, please read this manual thoroughly and retain it for future reference. RCP-D50/D51 2004 by Sony Corporation WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. AVERTISSEMENT Afin d'éviter tout risque d'incendie ou d'électrocution, ne pas exposer cet appareil à la pluie ou à l'humidité. Afin d'écarter tout risque d'électrocution, garder le coffret fermé. [. . . ] The items displayed differ according to whether the unit is in Advanced Setting mode or in Normal Setting ) in the table below are mode. The items shaded ( displayed only in Advanced Setting mode. Switching between Normal Setting mode and Advanced Setting mode is performed in RCP Config (Security Status) on the OTHERS menu. Paint menu (with the DXC-D30/D35 series) Paint menu consists of pages 1 to 4. You can select page 1 through 3 directly by pressing the MENU buttons, PAINT 1, PAINT 2, or PAINT 3. Pressing vor V of the page selected with a MENU button flip pages 1 through 4 in sequence. Page Menu Submenu Control item Paint 4 can also be selected by pressing the PAINT 3 button. Function Paint 1 White White Preset Auto Manual ATW To retrieve the preset white balance settings in the camera To select the auto white balance adjustment mode To select the manual white balance adjustment mode To turn ON/OFF the Auto Tracing White function (which automatically adjusts the white balance when lighting conditions change) To adjust the gain for the R signal in the white when Manual is pressed To adjust the gain for the B signal in the white when Manual is pressed To select the auto black balance adjustment mode To select the manual black balance adjustment mode To adjust the gain of the R signal in the black To adjust the gain of the B signal in the black To adjust the master black To turn the flare (black level when flare is generated) correction function ON/OFF To adjust the amount of flare correction for the R signal To adjust the amount of flare correction for the G signal To adjust the amount of flare correction for the B signal To turn ON/OFF the DynaLatitude function (for automatically setting the contrast between the bright and dark areas by detecting the levels of the subject in these areas) To turn ON/OFF the mode that uses the preset knee correction value To turn the Auto Knee circuit ON/OFF To adjust the gamma level To adjust the level at which the knee correction starts. As the value becomes larger, the start level decreases, which enhances the knee correction effects. To adjust the knee slope (amount of knee correction) ·R ·B Black Auto Manual ·R ·B · Master Flare Flare Off ·R ·G ·B Gamma/Knee DL Knee Preset Auto Knee · Gamma · Knee Point · Knee Slope 27 Menu Configuration and Basic Menu Operations Page Menu Submenu Control item Function Paint 2 Detail Detail 1 · Level · H/V Ratio To adjust the detail (contour correction) level To adjust the ratio of V (vertical) detail to H (horizontal) detail in detail correction. As the value becomes larger, the V detail ratio increases. To adjust the boost frequency (thickness of contour lines) for the detail correction To adjust the limit value for vertical detail To adjust the crispening level (appropriate level at which details of noise signals are removed) To adjust the level dependence (level at which the detail signal starts being suppressed) To adjust the amount of suppression of highlight detail (detail added to a high-luminance area) To adjust the amount of detail added after gamma correction To turn the aperture correction ON/OFF To turn ON/OFF the detail correction to the level higher than the knee point To adjust the amount of aperture correction To adjust the amount of detail correction to the level higher than the knee point To turn the red comb filter in the detail circuit ON/OFF. If OFF is selected, clarity improves, but cross color increases. To turn the green comb filter in the detail circuit ON/OFF. If OFF is selected, clarity improves, but cross color increases. To adjust the cross color suppress level to suppress the phenomenon of color jittering or coloring when a minutely striped pattern is shot To turn ON/OFF the skin gate area (target color range of skin detail correction or skin matrix adjustment) To turn the skin detail function (which suppresses the contour correction in the selected area) ON/OFF The unit will go to Standby mode when this button is pressed, and will automatically start obtaining the skin gate area data when Start is pressed. To adjust the amount of skin detail correction. As the value becomes larger, the amount of detail in the skin gate area decreases. To adjust the R­Y and B­Y ranges of the skin gate area (for setting each range to the same value at the same time) To adjust the R­Y range of the skin gate area To adjust the B­Y range of the skin gate area To turn the display of skin gate area ON/OFF To turn the skin detail function ON/OFF The unit will go to Standby mode when this button is pressed, and will automatically start obtaining the skin gate area data when Start is pressed. To adjust the skin detail level To adjust the R­Y and B­Y position of the skin detail gate area (for setting each range to the same value at the same time) To adjust the R­Y position of the skin detail gate area To adjust the B­Y position of the skin detail gate area · Frequency · V-Limit Detail 2 · Crispening · Level Dep · High L. · AFT GAM Detail 3 Aperture Knee Apert · Aperture · Knee Apert Cross Color Comb Filter R Comb Filter G · CCS Level Skin Detail Skin Detail 1 Detail Gate Skin DTL Auto Skin · Level · Size · R-Y · B-Y Skin Detail 2 Skin Gate Skin DTL Auto Skin · Level · Posi · R-Y · B-Y 28 Page Menu Submenu Control item Function Paint 2 (cont. ) Black STR Black Stretch 1 · Level To adjust the black stretch level · Stretch Level/Point 1 To adjust the upper limit of the signal levels that activate the black stretch function · Stretch Level/Point 2 To adjust the lower limit of the signal levels that activate the black stretch function Black Stretch 2 · Level · Compress Level/ Point 1 · Compress Level/ Point 2 To adjust the black stretch level To adjust the upper limit of the signal levels that activate the black compress function To adjust the lower limit of the signal levels that activate the black compress function To turn ON/OFF the DynaLatitude function (for automatically setting the contrast between the bright and dark areas by detecting the levels of the subject in these areas) To turn ON/OFF the mode that uses the preset knee correction value To turn the Auto Knee function ON/OFF To select the level of the DynaLatitude effects (Low/STD/High) To adjust the level at which the knee correction starts. As the value becomes larger, the start level decreases, which enhances the knee correction effects. To adjust the knee slope (amount of knee correction) To adjust the master gamma To set the value of the initial part of the gamma curve for low brightness to 3. 5 To set the value of the initial part of the gamma curve for low brightness to 4. 0 To adjust the level of the R gamma To adjust the level of the B gamma To turn the matrix ON/OFF To adjust the hue of the linear matrix To adjust the color saturation of the linear matrix To adjust the color tone for the R­G, G­B, or B­R elements of the matrix To adjust the color tone for the R­B, G­R, or B­G elements of the matrix To select the skin matrix function ON/OFF To adjust the hue of the designated area To adjust the color saturation of the designated area To adjust the amount of white clip (the highest white level). As the value becomes larger, the output level decreases. To turn the TLCS (total level control) function ON/OFF To set the f-stop value (f-2, f-2. 8, f-4, or f-5. 6) at which the iris control is switched to AGC (auto gain control) To set the upper limit value for the AGC (3 dB/6 dB/9 dB/12 dB/18 dB) adjustment To set the f-stop value (f-5. 6, f-8, f-11, or f-16) at which the iris control is switched to the AE (auto exposure) To select the standard auto iris mode To select the auto iris mode for shooting spot-lit subjects To select the auto iris mode for shooting back-lit subjects To select the intelligent auto iris mode a) Paint 3 Knee/DL DL Knee Preset Auto Knee · DL · Point · Slope Gamma · Master Init 3. 5 Init 4. 0 ·R ·B Matrix Matrix 1 Matrix Off · Hue · Sat Matrix 2 Matrix 3 Skin Matrix · R-G/· G-B/· B-R · R-B/· G-R/· B-G Skin Matrix · Hue · Sat Paint 4 White Clip TLCS · Master TLCS · AGC/C. Point · AGC/Limit · AE/C. Point Auto Iris STD Spot Light Back Light AI a) Only with models with the AI function 29 Menu Configuration and Basic Menu Operations Page Menu Submenu Control item Function Paint 4 (cont. ) CLS/EVS TLCS Shutter CLS To turn the TLCS (total level control) function ON/OFF To turn the shutter function ON/OFF To turn the CLS (clear scan) function (which reduces noise on the horizontal scan lines when the monitor screen connected to a PC is shot) ON/OFF To turn the EVS mode (which reduces flicker by increasing the vertical resolutions) ON/OFF To select the shutter speed To adjust the CLS frequency EVS · Shutter · CLS Function menu (with the DXC-D30/D35 series) Menu Submenu Control item Function Operation Jump menu 1 Jump menu 2 Jump menu 3 Jump menu 4 Jump menu 5 Jump menu 6 Jump menu 7 Shutter · Shutter CLS · CLS TLCS · Master Gain To jump to the adjustment screen designated for Menu 1 in Menu Set a)(Default: White of Paint 1) To jump to the adjustment screen designated for Menu 2 in Menu Set a) (Default:Black of Paint 1) To jump to the adjustment screen designated for Menu 3 in Menu Set a) (Default: Flare of Paint 1) To jump to the adjustment screen designated for Menu 4 in Menu Set a) (Default: Gamma/Knee of Paint 1) To jump to the adjustment screen designated for Menu 5 in Menu Set a) (Default: Detail of Paint 2) To jump to the adjustment screen designated for Menu 6 in Menu Set a) (Default: Skin Detail of Paint 2) To jump to the adjustment screen designated for Menu 7 in Menu Set a) (Default: Matrix of Paint 3) To turn the shutter function ON/OFF To select the shutter speed To turn the CLS (clear scan) function ON/OFF To select the CLS frequency To turn the TLCS (total level control) function ON/OFF To select the master gain value among ­3/0/3/6/9/12/18/18+DPR/24/24+DPR/HYPER Gain To turn the skin detail function ON/OFF To turn ON/OFF the display for the skin detail gate area (target color range for the skin detail correction or the skin matrix adjustment) To turn the ATW (auto tracing white balance) function (which automatically adjusts the white balance when lighting conditions change) ON/OFF To turn the TLCS (total level control) function ON/OFF To turn the Auto Knee function ON/OFF To turn the skin matrix function ON/OFF To turn the flare correction function ON/OFF (OFF while the button is lit) To turn ON/OFF the detail correction to the level higher than the knee point To turn the aperture correction ON/OFF To turn ON/OFF the DynaLatitude function (for automatically setting the contrast between the bright and dark areas by detecting the levels of the subject in these areas) To turn the white clip function ON/OFF (OFF while the button is lit) To turn the detail adjustment function ON/OFF (OFF while the button is lit) To turn the gamma adjustment function ON/OFF (OFF while the button is lit) To turn the linear matrix adjustment function ON/OFF (OFF while the button is lit) SW Page1 Skin Detail Detail Gate ATW TLCS Auto Knee Skin Matrix Flare Off Page 2 Knee Aperture Aperture DL White Clip Off Detail Off Gamma Off Matrix Off a) The submenu "Menu Set" can be selected from Security of RCP Config on the OTHERS menu. 30 Menu Submenu Control item a) Function Lens/Pan Option 1 Option 2 · Focus b) · Zoom · Pan c) · Tilt c) b) To turn the option control function 1 ON/OFF To turn the option control function 2 ON/OFF To adjust the focus To adjust the zoom To adjust panning of the tripod head To adjust tilting of the tripod head a) The item "Lens/Pan" is displayed when Pan/Tilt Enable is set to ON with Security of RCP Config on the OTHERS menu. [. . . ] The CLS frequency does not exceed the limit for the camera. · When adjusting the white balance, black balance and flare with the command link, select Manual Adjustment mode for white balance, black balance and flare also on slave units. 4 5 Press and highlight the button for the item for which you wish to activate the command link. When you adjust the item for which you wish to activate the command link on the master unit, the adjustment becomes valid on the cameras connected to the slave units. 58 Memory Sticks Using a Memory Stick When a Memory Stick is inserted in the panel, the file data can be stored on the Memory Stick, which enables you to share data among RCPs. Notes on Memory Stick On Memory Stick Memory Stick is a new compact, portable and versatile IC recording medium with a data capacity that exceeds that of a floppy disk. Memory Stick is specially designed for exchanging and sharing digital data among Memory Stick compatible products. [. . . ]