User manual SONY RDH-GTK11IP

[. . . ] 4-418-233-11 (1) Location of Controls Unit (Top) Getting Started  Power Setting the clock 1 Press   to turn on the system. 2 Press TIMER MENU  to select the clock set mode. If “PLAY SET” flashes, press /  repeatedly to select “CLOCK, ” and then press (enter) . Connect the power cord to a wall outlet. The demonstration appears on the display . [. . . ]  Move the remote closer to the system.  The batteries of the remote may be exhausted. Replace the batteries (R6/size AA) with new ones. “OVER CURRENT” appears. Sleep Timer: Severe hum or noise. You can fall asleep to music. This function works even if the clock is not set. Press SLEEP  repeatedly to select the desired time. To cancel the Sleep Timer, press SLEEP  repeatedly until “OFF” appears.  A problem has been detected with the level of electrical current from (USB) port . Turn off the system and remove the USB device from the (USB) port . Make sure there is no problem with the USB device. If this display pattern persists, contact your nearest Sony dealer. To turn off the automatic standby function There is no sound. This system is equipped with an automatic standby function. With this function, the system enters standby mode automatically in about 30 minutes when there is no operation or audio signal output. By default, the automatic standby function is turned on. Use buttons on the unit to turn off the automatic standby function. Hold down   while the system is on, until “AUTO. STBY OFF” appears. To turn on the function, repeat the procedure until “AUTO. STBY ON” appears.  The message “AUTO. STBY” start flashing on the display about 2 minutes before entering standby mode.  The automatic standby function is invalid for the tuner function (FM/AM), even when you have enabled it.  The system may not enter standby mode automatically in the following cases;  hen an audio signal is detected. d  hile the preset Play Timer or Sleep Timer is in process. w Specifications Amplifier section The following are measured at AC 120 V  240 V, 50/60 Hz (Latin American models (except for Mexican and Argentine models)) The following are measured at AC 127 V, 60 Hz (Mexican model) The following are measured at AC 220 V  240 V, 50/60 Hz (European, Russian, Australian and Argentine models) The following are measured at AC 120 V  240 V, 50/60 Hz (Other models) FST-GTK33iP/RDH-GTK33iP Power output (rated): 100 W + 100 W (at 3. 5 Ω, 1 kHz, 1% THD) RMS output power (reference): 210 W + 210 W (per channel at 3. 5 Ω, 1 kHz) FST-GTK11iP/RDH-GTK11iP Power output (rated): 55 W + 55 W (at 3 Ω, 1 kHz, 1% THD) RMS output power (reference): 115 W + 115 W (per channel at 3 Ω, 1 kHz) 3 Press +/  repeatedly to select the desired preset number. If another station is already assigned to the selected preset number, the station is replaced by the new station. The remote does not function.  The USB device is not connected correctly. Turn off the system, then reconnect the USB device. There is noise, skipping, or distorted sound. Play Timer: 4 Press  to store the station. 5 Repeat steps 1 through 4 to store other stations. You can preset up to 20 FM and 10 AM stations. You can wake up to FM/AM reception, iPod/iPhone or USB device at a preset time. Make sure you have set the clock. 1 Prepare the sound source. Prepare the sound source, and then press VOLUME +/  to adjust the volume. 6 To call up a preset radio station, press TUNING MODE  repeatedly until “PRESET” appears, and then press +/  repeatedly to select the desired preset number. 2 Select the timer set mode. Press TIMER MENU . The standby indicator  remains lit after unplugging the power cord.  Turn off the system, then reconnect the USB device. [. . . ] The display is turned off to conserve power. The timer and clock continue to operate. The clock is displayed. General The demonstration appears on the display  after plugging in the power cord even though the system is not turned on.  Press DISPLAY  once while the system is off. See “Setting the clock. ” USB device The connected iPod/iPhone or USB device is not being charged, when both are connected at the same time.  You cannot charge an iPod/iPhone and the USB device at the same time. [. . . ]