User manual SONY RM-921

[. . . ] · Do not use a new battery with old ones. · Do not mix the alkaline batteries and other kinds of batteries. · Do not expose the remote sensor of the receiver to direct sunlight or lighting apparatuses. · If you do not use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. [. . . ] This setting is ideal for movies encoded in Dolby Surround. In addition, this mode reproduce sound in 5. 1 channels when watching videos of overdubbed or old movies. · PLII MUSIC Performs Pro Logic II Music mode decoding. This setting is ideal for normal stereo sources such as CDs. · Neo:6 Cinema Performs the DTS Neo:6 Cinema mode decoding. This setting is ideal for movies encoded in DTS surround. · Neo:6 Music Performs the DTS Neo:6 Music mode decoding. This setting is ideal for normal stereo sources such as CDs. 15GB Programming the remote You can customize the remote to match the components connected to your receiver. You can even program the remote to control nonSony components and also Sony components that the remote is normally unable to control. The procedure below uses as an example a case in which a Aiwa VCR is connected to the VIDEO2 jacks on the receiver. Before you begin note that: ­ You cannot change the settings of PHONO. c*POWER *PREVIOUS *NEXT 3 Move the easy scroll key to select the time to delay the output of an IR code, then press the key to enter the selection. You can specify from 1 to 10 second delay (in 1 second increments). 7 Move the easy scroll key to select the IR code for the operation you want to perform, then press the key to enter the selection. To erase a programmed IR code 1 In step 5, move the easy scroll key to select "Common", then press the key to enter the selection. The program number list reappears. <MACRO1> c 1-POWER 2-NO SET 3-NO SET 2 Move the easy scroll key to select "NO SET", then press the key to enter the selection. 8 Repeat steps 4 through 7 to program up to 16 IR codes. To turn off all Sony components (SYSTEM STANDBY) 1 In step 5, move the easy scroll key to select "Common", then press the key to enter the selection. When you have finished programming IR codes, select "Exit" in step 7. To use learned codes under the Macro Play function 2 Move the easy scroll key to select "ALL OFF", then press the key to enter the selection. However, this function cannot be applied to some Sony components. 1 In step 5, move the easy scroll key to select "Button", then press the key to enter the selection. 18GB To cancel programming Move the easy scroll key to select "Exit" or "Cancel" during any step, then press the key to enter the selection. Tips · When the Macro Play function does not work properly, set "WAIT TIME" between each operation. Using the lists · In step 7, when no indication appears in front of the function name, no IR code is programmed. You cannot use the function for the macro play. · In step 4 and 7, when "NO SET" is displayed after the program number, the codes have not been programmed for the macro play. · In step 5, when you select "Button", ­ If "x" appears in the list in step 7, the button is already learned. ­ If you press < or > after you select the program step in step 7, the programmed IR code is emitted and you can check the operation. Note If you select "IR SET" for a component that already has a learned button setting, the learned codes for that component are cleared. Furthermore, if the cleared learned button is used in a Macro play setting, the setting for that button will be changes to "NO SET". Starting macro play 1 Press INPUT SELECTOR. The input list appears. USER1 USER2 cMACRO1 MACRO2 2 Move the easy scroll key to select "MACRO1" or "MACRO2", then press the key to enter the selection. The IR codes appear in the display window as they are performed. Notes · Pressing any of the following buttons during a macro play operation will cancel the macro play sequence before it is complete. ­ AV ?/1 ­ ?/1 ­ SYSTEM STANDBY ­ SOUND FIELD ­ INPUT SELECTOR ­ RM SET UP 19GB Using the RECEIVER menu 1 Press I repeatedly. Learning the commands of your components By using the Learning function, it is possible for this commander to perform learned operations. The RECEIVER menu appears. [. . . ] If you do the procedure below to turn off the backlight, you can make the batteries last longer. 3 Move the easy scroll key to select "+" or "­", then press the key to enter the selection. Each time you press the key, the contrast of the display changes. To exit adjusting, move the easy scroll key to select "Exit", then press the key to enter the selection. continued 25GB Switching the COMMAND MODE You can switch the command mode (AV SYSTEM 1 or AV SYSTEM 2) of the remote. If the command mode of the receiver and the remote is different, you cannot use the remote to operate the receiver. Besides, you can set the remote for the 2nd zone mode or 3rd zone mode (models of area code U, CA only). Set the command mode of the remote to the 2nd zone mode. [. . . ]