User manual SONY RM-AV2500T

[. . . ] The RM-AV2500T Remote Commander provides centralized control of all your AV components from a single remote commander and saves the trouble of operating different AV components with different remote control devices. Centralized control of Sony AV components with this one remote commander When you operate a lot of equipment all together, you need not change the screen. When watching a DVD, the DVD run system key, the Power key for TV and Receiver or the input change key can be displayed on one screen, and it can be operated, without switching the screen. This Commander is preset at the factory to operate Sony brand components, so you can use it out of the box as a control centre for your Sony AV components. [. . . ] When you want to set a new programme to this Component Select button, follow Steps 1 to 2 on page 28. Learnable SYSTEM CONTROL keys and number keys flash in the display panel. CONTROL buttons (A, B, or C), number keys or the Component Select button whose interval you want to change. When using Sony components, you can programme the Power-on signal for each component on a Component Select button. You can select the desired component and turn it on by just pressing that Component Select button. The number of the current setting stays lit and other numbers flash. The selected number stays lit and other numbers flash. Even if you have programmed a signal by "learning" (See "Adding a command that is required when selecting a component" on page 32. ) or a System Control function (page 27) for a Component Select button, you can programme the Power-On function for that button, but it cannot be used. If you clear a "learned" signal or the System Control function from the button, you can use the Power-On function. You can programme a signal by "learning" (page 32) or a System Control function (page 27) for a Component Select button for which the Power-On function has been programmed. In this case, the Power-On function is overwritten and cannot be used. If you clear the "learned" signal or the System Control function from the button, the PowerOn function is resumed, and you can use it again. If you have programmed both a signal by "learning" and a System Control function for the button, the "learned" signal will have overwritten the System Control function. When the Power-on command is programmed, you will hear a beep and "1 ON" appears on the display. (The display goes off when you release the buttons. To clear the Power-on command Adding a command that is required when selecting a component In addition to the original function of selecting the operating keys and buttons of the desired component, the Component Select button can have another remote control signal by "learning. " For example, if you always have to change input select of the amplifier to CD when listening to the CD player, programme the signal of "changing the amplifier's input select" to the CD button of this Commander. Then whenever you press the CD button, it automatically works as the original CD Component Select button and changes also the amplifier input select to CD. (In this case, the amplifier should be turned on first. Some specific remote control signals may not be learned. Head with your component's remote control. [. . . ] KEY DISPLAY 1 FUNCTION To turn the power on/off KEY DISPLAY 1 1 ­ 9, 0 +10 ENTER AUDIO DISPLAY CLEAR REPEAT TITLE SUB TITLE MENU R r t T OK m N M x X Z REC* MODE FUNCTION To turn the power on/off Number keys: To set items selected from the screen To select numbers 10 and above To enter a setting or to set items selected from the screen To change the sound To show the current play status on the screen To clear the selected characters from the screen To go into the repeat mode To display the title menu To switch the subtitle To display the DVD menu To move the cursor upward To move the cursor downward To move the cursor to the right To move the cursor to the left To execute items selected from the screen To rewind To play To fast-forward To stop To pause To eject a cassette To record To change the playback mode 1 ­ 9, 0, 1-, -/--, To change the channel 2-, ENTER For example, to change to channel 5, press 0 and 5 (or, press 5 and ENTER) INPUT DISPLAY ANT/SW MENU R r t T OK m N M REC* x X Z To change the input mode To activate the on-screen display To switch the antenna output To call the MENU display To move the cursor upward To move the cursor downward To move the cursor to the right To move the cursor to the left To enter the selection of the MENU display To rewind To play To fast-forward To record To stop To pause To eject a cassette Channel down: ­ EXIT To exit the mode * To avoid accidental recording, the REC key does not work unless pressed for more than 1 second (factory setting). To change this setting, see "Adjusting the beam interval to avoid key misoperation" on page 51. KEY DISPLAY FUNCTION KEY DISPLAY 1 FUNCTION To turn the power on/off > To proceed to the next (PROGRAM +) location or song Channel up . (PROGRAM ­) A/B To proceed to the previous location or song Channel down To decide the distance between A and B To select the deck * To avoid accidental recording, the REC key does not work unless pressed for more than 1 second (factory setting). [. . . ]