User manual SONY RM-AV3100

[. . . ] 2-055-287-12(1) Integrated Remote Commander Operating Instructions RM-AV3100 © 2004 Sony Corporation WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. WARNING You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. NOTICE FOR THE CUSTOMERS IN THE U. S. A. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] 2 While pressing the DEL key, press the Component Select button (or Label key) of the System Control function you want to clear. To change the Label keys, press the OTHER button repeatedly. 3 Follow Steps 4 to 7 on page 34. Notes · You can program the System Control functions for a Component Select button or a Label key on which the Power-On function (page 44) has been programmed. In this case, the Power-On function is overwritten and cannot be used. If you clear the System Control functions for the button, the PowerOn function is resumed, and you can use it again. · You cannot program the System Control functions for a Component Select button or a Label key for which a signal has been programmed by "learning" (page 46). ("NG" flashes on the display. ) · You can program the Power-On function (page 44) for a Component Select button or a Label key for which a System Control function has been programmed, but the Power-On function cannot be used. If you clear the System Control function from the button, you can use the Power-On function. · If you interrupt the procedure at any point for over two minutes, the setting mode ends and the series of commands will be programmed to that point. In this case, clear the program and start again from Step 1 to set the entire program from the beginning. You cannot continue from where you let off. · If you change the component code number (page 12) or program a new signal by learning (page 20) for a key or button that has been programmed with the series of commands of a System Control function, the new signal will be transmitted when you press the corresponding Component Select button or a Label key. 3 Press COMMANDER OFF. COMMANDER OFF If you keep COMMANDER OFF pressed for more than 2 seconds The Commander turns off. If you keep COMMANDER OFF pressed for less than 2 seconds The Commander returns to the previous setting mode. 40 Changing the interval between operation steps You can control the interval from 100 900 ms in units of 50 ms. 3 Press the MODE key. "MODE" appears on the Mode Display key. 2 3, 6 TV STB VCR DVD CD AMP OTHER 4 5 8 4 Press the SYSDELAY key. SYSDELAY SYSTEM CONTROL TIMER COMMANDER LIGHT OFF 1 2 3 MORE VOLUME CHANNEL OK MENU EXIT MUTING RECALL 1 1 While pressing COMMANDER OFF, press MUTING. COMMANDER OFF MUTING "SYSDELAY" is displayed on the Mode Display key. "SET" appears on the Mode Display key. 5 Select the system number, the component name or the timer program number of the interval you want to change by pressing the SYSTEM CONTROL button, the Component Select button or the Label key. To change the Label keys for system numbers Press the MORE button repeatedly. 2 Press the Mode Display key (SET) twice to display "MODE" on one of the Label keys on the display. To display and change the Label keys for component names Press the OTHER button repeatedly. Continued 41 Executing a Series of Commands -- System Control Functions (continued) To display and change the Label keys for timer program numbers Press the TIMER button repeatedly. For timer settings, see page 64. 8 Press COMMANDER OFF. COMMANDER OFF If you keep COMMANDER OFF pressed for more than 2 seconds The Commander turns off. When you select the Component name, go to Step 6. If you keep COMMANDER OFF pressed for less than 2 seconds The Commander returns to the previous setting mode. When you select the system number or the timer program number, go to Step 7. 6 Press the INTERVAL key. The current interval setting stays lit, and (+) and (­) flash. 7 Press the (+) or (­) key to change the interval. You can control the interval from 100 to 900 ms in units of 50 ms. Each time you the (+) key is pressed, the interval increases by 50 ms. Each time you the (­) key is pressed, the interval decreased by 50 ms. (ms: 1/1000 second) 42 To change the component macro executing time 1 Follow the procedure of Steps 1 5 on page 41. 4 Press COMMANDER OFF. COMMANDER OFF If you keep COMMANDER OFF pressed for more than 2 seconds The Commander turns off. 2 Press the TIME key. If you keep COMMANDER OFF pressed for less than 2 seconds The Commander returns to the previous setting mode. The current component macro executing time stays lit, and (+) and (­) flash. 3 Press the (+) or (­) key to change the component macro executing time. You can control the time from 0 to 2 sec (seconds) in units of 1 sec. Each time you the (+) key is pressed, the time increased by 1 sec. Each time you the (­) key is pressed, the time decreases by 1 sec. 43 Adding an Extra Function to the Component Select Buttons Programming the Power-On command of the selected component (for Sony components only) When using Sony components, you can program the Power-on signal for each component on a Component Select button or a Label key. You can select the desired component and turn it on by just pressing that Component Select button or a Label key. Example: To program the TV button 1 While pressing COMMANDER OFF, press MUTING. COMMANDER OFF MUTING "SET" appears on the Mode Display key. 2 Press the Mode Display key (SET) twice to display "MODE" on one of the Label keys on the display. 2 3, 4 5 TV STB VCR DVD CD AMP OTHER SYSTEM CONTROL TIMER LIGHT COMMANDER OFF 3 Press the MODE key. "MODE" appears on the Mode Display key. 1 2 3 MORE 1 VOLUME CHANNEL OK MENU EXIT MUTING RECALL 44 4 Press the PowerON key. PowerON To clear the Power-on command Repeat the procedure above. The following display appears. "PowerON" appears on the Mode Display key. 6 Press COMMANDER OFF. COMMANDER OFF The display of the component names (preset by Sony) for which you can program the Power-on signal flashes. The display of the other components stays lit. If you keep COMMANDER OFF pressed for more than 2 seconds The Commander turns off. If you keep COMMANDER OFF pressed for less than 2 seconds The Commander returns to the previous setting mode. 5 Select the desired component by pressing the Component Select button or the Label key. (To change the Label keys, press the OTHER button repeatedly. ) TV The selected component name appears on the Mode display key and "POWER ON" appears on the display with a beep sound. Continued 45 Adding an Extra Function to the Component Select Buttons (continued) Notes · If the component code of a non-Sony product has been set for a Component Select button or a Label key, you cannot program the Power-On function for it. · Even if you have programmed a signal by "learning" (See "Adding a command that is required when selecting a component, " page 46) or a System Control function (page 39) for a Component Select button or a Label key, you can program the Power-On function for that button, but it cannot be used. If you clear a "learned" signal or the System Control function from the button or key, you can use the Power-On function. · You can program a signal by "learning" (page 46) or a System Control function (page 39) for a Component Select button for which the Power-On function has been programmed. [. . . ] the clock setting mode by Replace the batteries with new ones (page 7). So, to use the Commander with the previous set contents, you should only set the clock (page 8). "LOCK" is displayed on · The Hold function is on. the LCD and the display for operation does not appear when you press a button. For the customers in the U. S. A. Customer Support Information After you have read through this manual, if you still cannot get the Remote Commander to work properly, call the Sony Customer Support Helpline at 1-800-822-2217. 94 Appendix Table of Preset Functions Note There may be some components or functions that cannot be operated with this Commander. KEY DISPLAY FUNCTION Channel down: ­ CHANNEL +/­ Channel up: + RECALL To operate JUMP, FLASHBACK or CHANNEL RETURN function on the TV depending on the setting of the TV's manufacturer Volume up: + Volume down: ­ To mute the volume on the TV. [. . . ]