User manual SONY RM-PCM1

[. . . ] For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product. Features The RM-PCM1 Remote Commander provides centralised control of all your AV components from a single remote commander and saves the trouble of operating different AV components with different remote control devices. The following are its main features. Centralised control of Sony AV components with this one remote commander This Commander is preset at the factory to operate Sony brand components, so you can use it out of the box as a control centre for your Sony AV components. Remote control signals for non-Sony components are also preset Disposal of waste batteries (applicable in the European Union and other European countries with separate collection systems) This symbol on the battery or on the packaging indicates that the battery provided with this product shall not be treated as household waste. By ensuring these batteries are disposed of correctly, you will help prevent potentially negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of the battery. The recycling of the materials will help to conserve natural resources. [. . . ] If you change the component code (page 8) after setting the Power-On function, the Power-On function is cleared. (The Component Select button flashes twice to indicate that you cannot set this function. ) · Even if you used the Learning function (page 12) to programme a signal on a Component Select button, you can programme the Power-On function on that button but it cannot be used. If you clear the "learned" function on that button, you can use the Power-On function. Executing a Series of Commands -- System Control Functions With the System Control function, you can programme a series of operating commands, and execute them by pressing just one button. You can programme up to 16 consecutive operation steps to each of the SYSTEM CONTROL buttons (A ­ D). If you have set the System Control function for a Component Select button (page 23), the execution of the programmed commands begins when you press the Component Select button for more than 2 seconds. When executing the programmed commands, each remote commander signal is transmitted. Example: To watch a video, you can set a series of operations as follows: Power on the TV. r Set the input selector of the amplifier to VIDEO 1. r Set the input mode of the TV to VIDEO 1. r Start video playback. 1, 3 SET 1 TV VCR VIDEO1 DVD CD SAT TAPE CBL AMP AUX VIDEO2 1 TUNER 2 CD 3 TAPE 4 MD 5 TV 6 PHONO 7 -/-1 8 DVD 9 ENT 2 PROGRAM 0 DIGITAL ANALOG 2 MENU GUIDE OK RETURN TOOLS SYSTEM CONTROL A B C D 1 Continued 21 Example: To programme the procedure above to the SYSTEM CONTROL B button To programme a new series of operations for those buttons which already have a Control Programme set Erase the programme (page 22). Notes · If you interrupt the procedure at any point for over 20 seconds, the setting mode ends and the series of commands will be programmed up to that point. In this case, clear the programme (page 22) and start again from Step 1 to set the entire programme from the beginning. You cannot continue programming once the setting mode ends. Once if you set a Component Select button to a different type of component, the entered component`s code number becomes effective. Notes · To use the original component setting, set the component code number again (page 8). · If you enter a new brand`s component code number without clearing the previous "learned" functions on that Component Select button, the previously "learned" functions remain effective. Erase the functions you do not use frequently. · You can only assign a TV to the TV Component Select button. 24 Using Other Functions Locking the Controls -- Hold Function To prevent accidental operation, you can lock all the buttons with the Hold function. While the Hold function is on, no function can be operated. (The SET indicator and the Component Select button currently selected flash twice. ) SET TV DVD CD (twice) SAT TAPE CBL AMP SET 1 1 VCR To unlock the control Press and while holding 1, press t and PROGRAM ­. The SET indicator and the Component Select button currently selected flash once, and the Hold function is released. SET TV VCR VIDEO1 DVD CD SAT TAPE CBL AMP AUX VIDEO2 1 TUNER 2 CD 3 TAPE 4 MD 5 TV 6 PHONO 7 -/-1 8 DVD 9 ENT 2 PROGRAM 0 DIGITAL ANALOG (once) DVD CD SAT TAPE CBL AMP 1 TV VCR 1 Press and while holding 1, press t and PROGRAM +. PROGRAM 1 + + The SET indicator and the Component Select button currently selected flash once, and the Hold function is set. SET TV VCR DVD CD SAT TAPE CBL AMP x All the buttons are locked. x SET TV VCR DVD CD (once) SAT TAPE CBL AMP 25 SET Erasing All Settings -- To reset the Commander to its factory settings You can erase all remote control signals programmed by the "learned" function to reset the Commander to its factory settings. TV VCR DVD CD SAT TAPE CBL AMP SET TV VCR DVD CD SAT TAPE CBL AMP SET SET 1 1 TV VCR DVD CD SAT TAPE CBL AMP TV VCR VIDEO1 DVD CD SAT TAPE CBL AMP AUX VIDEO2 1 TUNER 2 CD 3 TAPE SET TV VCR DVD CD SAT TAPE CBL AMP 4 MD 5 TV 6 PHONO 7 -/-1 8 DVD 9 ENT 2 PROGRAM 0 DIGITAL ANALOG 1 Press and while holding 1, press t and 2 ­. 1 + + When pressing the 1 button and the t button, all the Component Select buttons go off. When pressing the 2 ­ button while holding down the 1 button and the t button, the SET indicator lights up and the Component Select buttons light up one by one. When the SET indicator turns off at last, all settings are cleared, and the Commander returns to its original state. 26 Additional Information Precautions ·Do not drop the unit or give a shock to the unit, or it may cause a malfunction. ·Do not leave the unit in a location near heat sources, or in a place subject to direct sunlight, excessive dust or sand, moisture, rain or mechanical shock. ·Do not put foreign objects into the unit. Should any liquid or solid object fall into the unit, have it checked by qualified personnel before operating the unit any further. [. . . ] Programme down To display the title menu. qh (TITLE) MD KEY DISPLAY 01 9m 9N 9M 9REC z FUNCTION To turn on and off. To record, press N while pressing REC z*. 11 ­ 9, 0 To select the track number. [. . . ]