User manual SONY RM-V202WMSK

[. . . ] However, some functions explained in this section may not work depending on the model of the receiver. For the functions of the receiver you purchased, refer to the Operating Instructions supplied with the receiver. Press to set the receiver to automatically select the appropriate decoding mode for the input signal. ALT 8 Press to change remote key function to activate those buttons with orange printing. ANT* (After pressing ALT) qh When you selected VCR, press to select output signal from antenna terminal: TV signal or VCR program. AUDIO qk Parts description TV ?/1 AV ?/1 L USE MODE P Changing the sound to Multiplex, Bilingual or Multi channel TV sound. AV MENU qa ?/1 Press to display the menus of the VCR, satellite tuner, or DVD. 1 2 3 AV ?/1 wa wa SYSTEM STANDBY SLEEP w; ql qk qj qh qg 2CH 1 TEST TONE 4 AUDIO 7 A. F. D. 2 DIRECT 5 SWAP/ ANGLE 8 SUBTITLE MOVIE MUSIC 3 AAC SB BI-LING DECODING 6 JUMP/ TIME 9 ENTER 12 DISC ALT PRESET/ CH/D. SKIP 4 5 6 7 8 9 q; qa qs Press to turn the selected audio and video components on or off. If you press the ?/1 switch at the same time, it will turn off the receiver and other Sony audio/video components (SYSTEM STANDBY). Note . > 0/10 >10/11 SHIFT D. TUNING m ANT M - CLEAR SEARCH MODE N TOP MENU/ GUIDE X AV MENU x MUTING F G g f DISPLAY TV VOL MASTER VOL The function of the AV ?/1 switch changes automatically each time you select the input with the easy scroll key (3). [. . . ] · To activate the buttons with orange printing, press ALT first before pressing the buttons. · Before you use the V/v/B/b/ENTER/EXECUTE button for receiver operation, press MAIN MENU. To operate other components, press TOP MENU/ GUIDE or AV MENU after selecting the input. Location of Parts and Basic Remote Operations When you selected TV, press to select the channel entry mode, either one or two digit. V/v/B/b/ENTER/EXECUTE ed After pressing MAIN MENU, AV MENU, or TOP MENU/GUIDE, use the button to make specific settings, then press the button to enter the selection. H eg Press to start play. (Press to start play on the front sides of the cassette. ) X wh Press to pause play or recording, or press to start recording when the component is in recording standby. x wg Press to stop play. . /> wf Press to skip tracks. m/M qgqh Press to fast-forward or rewind. Press to search tracks in the forward or backward direction. * The function of these buttons switch automatically each time you select the input with the easy scroll key (3). Depending on the component, the above operation may not be possible or may operate differently than described. ** Only for Sony TVs with the picture-in-picture function. Notes · The AAC BI-LING and 12 buttons are not available. · Some buttons may not be used depending on the model. · The above explanation is intended to serve as an example only. Therefore, depending on the 7GB Table of buttons used to control each component When you program the remote to control the following Sony or non-Sony components, you can use the buttons on the remote that are marked with circles. Note, however, that some buttons may not operate your component. Component CD player DAT deck MD deck Tape deck (A and B) LD player VCR TV Satellite Video tuner/ CD Cable player box DVD player Button(s) AV ?/1 Numeric buttons H X x . /> m/M ANT D. SKIP** PRESET/CH +/­ SUBTITLE >10/11 AUDIO SWAP ANGLE JUMP TIME DISC** -/-SEARCH MODE ENTER AV MENU TOP MENU/GUIDE DISPLAY RETURN O EXIT V/v/B/b/ENTER/ EXECUTE CLEAR z z z z z z z z z z z z z z z z z z z z z z z z z z z z* z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z z * B deck only. You can also select the TV ?/1 button. To clear the learned codes Start again from step 1. After step 3, press TV ?/1 for more than 2 seconds. The USE MODE button blinks twice slowly and the learned code is cleared. If TV ?/1 is pressed less than 2 seconds, the learning procedure returns to the beginning of step 5. When a learned code is cleared, if the button was previously programmed for another input, the programmed code for that input can be used. 3 4 Press the button you want to use for the Learning function. The USE MODE button turns off while a valid button is pressed, then blinks slowly. Point the remote control code receiver section of the remote towards the receiver/transmitter on the remote control to be learned. m . N G F f g O > M X P - To use the learned input 5-10 cm x 5 Move the easy scroll key to select the learned input, then press the key to enter the selection. Press the appropriate button on the remote control to be learned to send the remote button code. To use a command that has been learned Select a learned input, then press the learned button for that input. Lightly pressing the button once should be sufficient. If learning is completed successfully, the USE MODE button slowly flashes twice 12GB To clear the memory of the remote Press ?/1, AV ?/1 and MASTER VOL ­ at the same time. The USE MODE button flashes 3 times, then goes off. Performing several commands in sequence automatically -- Macro Play The Macro Play function lets you link several IR codes in a sequential order as a single command. The remote provides 2 macro lists (M1 and M2). You can specify up to 10 IR codes for each macro list. Advanced Remote Operations Setting the sequence of IR codes 1 2 3 Press TV ?/1 while holding down USE MODE. The USE MODE button lights and "LEARN" appears in the display. Move the easy scroll key to select "M1" or "M2", then press the key to enter the selection. Press the numeric buttons to select the macro step number. For example, to program step 1, press 1. [. . . ] The USE MODE button lights twice slowly, then the remote automatically exits the macro setting mode. 1 2 Press ?/1 while holding down USE MODE. Move the easy scroll key to select "2ND", then press the key to enter the selection. The USE MODE button lights once, then the command mode switches. To start macro play Move the easy scroll key to select "M1" or "M2", then press the key to enter the selection Note To reset the remote to factory settings Press ?/1, AV ?/1, and MASTER VOL ­ at the same time. The USE MODE button lights 3 times, then goes off. If the Macro Play function does not work properly, program a delay between each operation. See "To delay the output of an IR code". 14GB Additional Information Specifications General Remote control system Power requirements Dimensions Mass (approx. ) Infrared control 3 V DC with two R6 (size-AA) batteries 210 × 49 × 27 mm 85 g excluding batteries Troubleshooting If you experience any of the following difficulties while using the receiver, use this troubleshooting guide to help you remedy the problem. [. . . ]