User manual SONY SA-FT3H

[. . . ] Thread the speaker cord A through the holes on the table top stand base B and the table top stand cover C and connect it to the speaker. Secure the table top stand cover C to the speaker with the M5 screws D. Secure the table top stand base B to the table top stand cover C with the M3. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. [. . . ] The speakers of this system can be installed in 2 ways, using table top stands or install to the wall. The accessories needed for each installation method are shown in the tables below. Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile attach the screws securely to a beam and fasten them to the wall. Contact a screw shop or installer regarding the wall material or screws to be used. Sony is not responsible for accident or damage caused by improper installation, insufficient wall strength or improper screw installation, natural calamity, etc. Use of this applicance with some systems may present a shock or fire hazard. Do not use with any units which have the following marking located near output. As ENERGY STAR® Partner, Sony Corporation has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. 1 channel speaker system consisting of two front speakers, two surround speakers (there is no difference between front and surround speakers), one center speaker, and one subwoofer. Hole on the back of the center speaker Orifice à l'arrière de l'enceinte centrale 300. Faites passer le cordon d'enceinte A par les orifices sur la base de support B et le couvercle de support C et raccordez l'enceinte. fixez le couvercle de support C à l'enceinte avec les vis M5 D. Fixez la base de support B au couvercle de support C avec les vis M3, 5 E. Faites passer le cordon d'enceinte A par les orifices de la base de support G de l'enceinte centrale et de l'ajustage de support de l'enceinte centrale H, et raccordez-le à l'enceinte centrale. fixez l'ajustage H de support d'enceinte centrale à l'enceinte centrale avec la vis M5 D. Fixez la base de support de l'enceinte centrale G au réglage de support de l'enceinte centrale H avec la vis M4 I. Pour les enceintes avant A Cordon d'enceinte (3, 5 m) × 2 Pour les enceintes surround F Cordon d'enceinte (10 m) × 2 Pour les enceintes avant / surround B Base du support ×4 C Couvercle du support × 4 D Vis (M5) × 4 E Vis (M3, 5) × 16 J Coussinet × 16 K Tampon arrière × 8 Enceinte centrale A Cordon d'enceinte (3, 5 m) × 1 G Base de support d'enceinte centrale ×1 H Ajustage de support d'enceinte centrale ×1 D Vis (M5) × 1 I Vis (M4) × 2 J Coussinet × 4 K Tampon arrière × 2 (D) Make sure power to all components (included the subwoofer) is turned off before starting the hook-up. Listening to the sound (I) First, turn down the volume on the amplifier. The volume should be set to minimum before you begin playing the program source. Should you encounter a problem with your speaker system, check the following list and take the indicated measures. Make sure the plus (+) and the minus (­) terminals on the speakers are matched to the corresponding plus (+) and minus (­) terminals on the amplifier. [. . . ] See the table below for the proper settings. Some amplifier functions for enhancing the sound may cause distortion in the subwoofer. To enjoy high-quality sound, do not turn the subwoofer volume too high. If the sound distorts when you turn on the bass reinforcement from your amplifier (such as, DBFB, GROOVE, the graphic equalizer, etc), turn down the bass reinforcement and adjust the level. [. . . ]