User manual SONY SA-FT7ED

[. . . ] If the glass breaks, it may cause serious injury. Do not drop objects from a high position or hit the glass. The glass may break instantly (or later) because of a tiny crack. If you find any crack on the tempered glass, consult the dealer or Sony Customer Service for exchange. [. . . ] This speaker system is magnetically shielded to allow it to be installed near a TV set. However, color irregularities may still be observed on certain types of TV sets. Thread the speaker cord () through the holes on the base () and the adjuster () of the center speaker stand, and connect it to the center speaker (-1). Secure the adjuster () to the center speaker with the screws (M4) () (-2). Secure the base () to the adjuster () with the screws (M5) () after adjusting the angle (-3). Turn off the TV set, then turn it on again in 15 to 30 minutes. When using the speakers with their stands, you can cover the screw holes for wall mounting on the back of the speakers with the supplied stickers. When installing the front/surround speakers on the wall, you can cover the screw holes on the bottom of the terminal adapters with the supplied stickers. Do not place the speakers in locations that are: -- Extremely hot or cold -- Dusty or dirty -- Very humid -- Subject to vibrations -- Subject to direct sunlight · Use caution when placing the speaker on a specially treated (waxed, oiled, polished, etc. ) floor, as staining or discoloration may result. Clean the speaker cabinets with the supplied cleaning cloth. If you have any questions or problems concerning your speaker system, please consult your nearest Sony dealer. Make sure power to all components (included the subwoofer) is turned off before hooking up. Speaker system Speaker units Enclosure type Rated impedance Power handling capacity Maximum input power: Sensitivity level Frequency range Dimensions (w/h/d) with floor stand 2 way, magnetically shielded Woofer: 10 cm, cone type Tweeter: 20 mm, dome type Bass reflex 8 ohms Set the volume level to best suit your preference according to the program source. Some material is recorded with strong emphasis on bass sounds, which may be excessive in some cases. If this happens, rotate BASS BOOST towards minimum. Make sure the plus (+) and the minus (­) terminals on the speakers are matched to the corresponding plus (+) and minus (­) terminals on the amplifier. Be sure to tighten the screws of the speaker terminals securely as loose screws may become a source of noise. Contact between bare speaker wires at the speaker terminals may cause a short circuit. Black or black striped wires are minus (­) in polarity, and should be connected to the minus (­) speaker terminals. Some amplifier functions for enhancing the sound may cause distortion in the subwoofer. To enjoy high-quality sound, do not turn the subwoofer volume too high. [. . . ] Type d'enceinte Impédance nominale Puissance admissible Puissance d'entrée maximale : 120 W Niveau de sensibilité 84 dB (1 W, 1 m) Gamme de fréquences 130 Hz - 70 000 Hz Dimensions (l/h/p) Environ 500 × 94 × 30 mm avec support de table Environ 500 × 108 × 66 mm avec support de fixation mural Environ 500 × 94 × 42 mm Poids Environ 1, 6 kg avec support de table Environ 1, 8 kg avec support de fixation mural Environ 1, 7 kg If you use the amplifier with adjustable crossover frequency, it is recommended to select 120 Hz (or close to this figure) as the crossover frequency for your front, center, and surround speakers. 5 m) (3) Speaker cord (10 m) (2) Pin cord (2 m) (1) Floor stand (2) Terminal adapter (4) Table top stand base (2) Center speaker stand base (1) Center speaker stand adjuster (1) Wall mounting bracket (for the front/surround speakers) (4) Wall mounting bracket (for the center speaker) (1) Wall mounting hook (10) Hex-head screw (8) Screw (M5) (10) Screw (M4) (20) Wrench (1) L-adapter (1) Sticker for the speakers (1) Sticker for the terminal adapters (4) Cleaning cloth (1) Design and specifications are subject to change without notice. Listening to the sound () First, turn down the volume on the amplifier. The volume should be set to minimum before you begin playing the program source. [. . . ]