User manual SONY SA-TA4

[. . . ] This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. With this Digital Satellite Receiver and the proper Satellite Dish Antenna, you may be able to receive local channels from DIRECTV in certain markets. Additional equipment may be required in some areas. Check with your retailer or visit www. directv. com for information on availability of local channels from DIRECTV in your area Owner's Record The model and serial numbers are located on the back of the Satellite Receiver. [. . . ] · This Remote Control cannot operate your VCR. Use your VCR's remote to operate your VCR. continued Programming Your Remote Control 27 Television Brand Press SELECT to choose your TV brand and continue. 3 4 Highlight and select your TV brand using the / / / /SELECT buttons. The available codes for your TV brand appear. SEARS SHARP SIEMENS SIGNATURE SONY SOUNDESIGN Enter the Remote Control code. a)Cover the IR emitter on the front end of the Remote Control. This prevents the Remote Control from operating your Satellite Receiver while you program the Remote Control. b)Press and hold the TiVo and POWER/TV buttons at the same time until the Remote Active indicator lights (about three seconds), then release the buttons. c)Use the number keys to enter one of the four-digit codes listed for your TV brand. The indicator flashes three times, indicating that you entered the code correctly. FPO Codes for SONY Possible codes for this device are: 0043, 0067, 0075, 0117, 0130, 0136, 0170 MUTING POWER/TV POWER FPO Program your TV PWR, VOL, and MUTE buttons: Point the PTV Remote away from the Recorder and hold down the TV PWR and TIVO buttons on the Remote for 5 sec. Enter the first code TiVo Button using the numbers on the Remote. If it doesn't work, try the next code. SAT 1 4 7 2 5 8 0 3 6 TV 9 d)Test the code by aiming your Remote Control at the TV and pressing the POWER/TV button. If the TV turns off, you have programmed the correct code. e)If the Remote Control did not turn off your TV, repeat steps 4a through 4d and try the next code listed for your TV. SELECT Note If you connected an audio system to your Satellite Receiver, you can program the Remote Control's POWER/TV, VOL (volume) and MUTING buttons to operate your audio system rather than your TV. In step 2c on the previous page, select "Remote A/V Stereo System", and continue the procedure. 28 Programming Your Remote Control Code Search Method The Remote Control has hundreds of available codes. · Verify that your phone line is working by disconnecting the phone cord from your Satellite Receiver, connecting it to a phone, and checking for a dial tone. · Make sure the phone cord is connected to the Satellite Receiver and the wall jack. · If you are getting a busy signal when connecting, try another local dial-in number from the Dial-In Number screen or try the call during off peak hours, before 3 pm or after 11 pm. · Try changing your phone dialing options by following the steps below. After making changes to phone dialing options, make a test call (press the TiVo button to go to TiVo Central, then choose Messages & Setup, then Receiver & Phone Setup, then Phone Connection and select "Make Test Call"). · If you have voice mail or other non-standard dial tone, press the TiVo button to go to TiVo Central, then choose Messages & Setup, then Receiver & Phone Setup, then Phone Connection, then Change Dialling Options and turn off "dial tone detection". · If you have call waiting, press the TiVo button to go to TiVo Central, then choose Messages & Setup, then Receiver & Phone Setup, then Phone Connection, then Change Dialling Options and disable call waiting by entering the correct prefix in "Call Waiting Prefix" (usually "*70, "). · If you use a dial prefix for outside lines, press the TiVo button to go to TiVo Central, then choose Messages & Setup, then Receiver & Phone Setup, then Phone Connection, then Change Dialing Options and set the "Dial Prefix" (for example, "9, "). Additional Information continued Troubleshooting 31 Symptom My Satellite Receiver isn't making the setup phone calls. (continued) Solution · If you have a low-voltage phone line, press the TiVo button to go to TiVo Central, then choose Messages & Setup, then Receiver & Phone Setup, then Phone Connection, then Change Dialling Options and turn off "phone availability detection". · If you have a caller ID box, try removing it from the line since some models interfere with the Satellite Receiver modem's ability to make a call. · If you use a fax machine or computer modem connected to the same phone line, make sure they are not using the line while your Satellite Receiver is trying to make a call. [. . . ] After this 90 day period, you must pay for all labor charges. Parts: For a period of one year from the original date of purchase, SONY will supply, at no charge, new or rebuilt replacements in exchange for defective parts. Any replacements will be warranted for the longer of the remainder of the original warranty period or 90 days from the installation of the parts by a SONY authorized DIRECTV System installer or facility. ­ If the Product was installed by a SONY authorized DIRECTV System installer, contact that installer for instructions. [. . . ]