User manual SONY SA-TT60

[. . . ] WARNING To reduce the risk of fire or shock hazard, do not expose the unit to rain or moisture. calls when the phone is available. If the phone jack is used for another phone, use the provided splitter. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. The Satellite Receiver is intended for use only within the United States. Local Programming This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of significant magnitude to constitute a risk of electric shock to persons. [. . . ] In step 2c on the previous page, select "Remote A/V Stereo System", and continue the procedure. 28 Programming Your Remote Control Code Search Method The Remote Control has hundreds of available codes. The correct code for your TV might be available, even if it is not listed for your TV brand in the on-screen Code Entry method. 1 Set the Remote Control to Code Search mode. a)Press and hold the TiVo and POWER/TV buttons at the same time until the Remote Active indicator lights (about three seconds), then release the buttons. b)Using the number keys on the Remote Control, enter 0999. 2 Notes · The Code Search method automatically programs the POWER/TV, VOL +/­, and MUTING buttons on the Remote Control. · If you have an audio system connected to the Satellite Receiver, you can program the POWER/TV button on the Remote Control to turn on and off both the audio system and your TV. To do so, use code 1999 instead of 0999 in step 1b. · To reset the Remote Control back to the manufacturer's settings, enter code 0981 in step 1b. Test the code. a)Aim the Remote Control at the TV, press POWER/TV and see if the TV turns off or on. b)If the TV does turn off and on, press MUTING and VOL (volume) +/­ to make sure they operate the TV. If these buttons operate the TV, go to step 4 below. 3 4 Press the CH (channel) + button to cycle to the next code, then test the code by repeating step 2 above. The Remote Control has hundreds of available codes. If the Remote Active indicator goes out, you have tested all of the codes. Press ENTER to set the code and exit Code Search mode. Additional Information Press CLEAR to exit Code Search mode without setting a new code. Programming Your Remote Control 29 Troubleshooting DIRECTV, TiVo and Sony are dedicated to providing you with quality support and customer service. If you have any questions or difficulties, first refer to the troubleshooting section in each manual. If you still need help, see below for the appropriate customer service department to contact: Contact Sony at 1-877-585-SONY (7669) if you need assistance with: · Connecting your Satellite Receiver with your TV and other A/V equipment. · Initial Guided Setup difficulties (e. g. · Programming the Remote Control to control your TV or A/V equipment. · A system that does not function properly after restart. · Questions about your Limited Warranty. Contact DIRECTV and TiVo customer support at 1-800-DIRECTV (347-3288) if you need assistance with: · Activating DIRECTV® programming. · Activating or using a feature of the TiVo Service. · Getting correct Program Guide data. · Understanding an on-screen message from TiVo regarding your TiVo Service account. You can also refer to the FAQ's listed in the web sites below. DIRECTV: http://www. directv. com TiVo: http://www. tivo. com Sony: http://www. sony. com/service or email at custserv@info. sel. sony. com When you call DIRECTV, you will need to reference your account number and/or Access Card number. When you call either DIRECTV or Sony, you will need to reference your model and serial number located on the inside of the back cover of the Viewer's Guide. [. . . ] ­ If the Product was not installed by a SONY authorized DIRECTV System installer, you must take the Product or deliver the Product in either its original packaging or packaging affording an equal degree of protection (with freight prepaid), to a SONY authorized DIRECTV System service facility. To locate the closest such facility, please call the telephone number listed below. This warranty does not cover customer instruction, installation, set up adjustments or signal reception problems. This warranty does not cover cosmetic damage or damage due to accident, misuse, abuse, negligence, commercial use, or modification of, or to any part of the Product. [. . . ]