User manual SONY SDM-HS75/B

[. . . ] 2-583-745-01(1) TFT LCD Color Computer Display Operating Instructions GB SDM-HS75 SDM-HS95 © 2004 Sony Corporation Owner's Record The model and serial numbers are located at the rear of the unit. Record these numbers in the spaces provided below. Refer to them whenever you call upon your dealer regarding this product. Model No. NOTICE This notice is applicable for USA/Canada only. [. . . ] Keep pressing m to scroll down until the icons in menu 9 and 0 appear. See page 11 for more information on using the m/M and OK buttons. 7 SHARPNESS (page 14) Select the SHARPNESS menu to adjust to sharpen the edge of images. S H AR P N E S S 5 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T 10 8 MENU POSITION (page 14) Select the MENU POSITION to change the onscreen menu position. 3 Adjust the menu. MENU POS I T I ON Press the m/M buttons to make the adjustment, then press the OK button. When you press the OK button, the setting is stored, then the display returns to the previous menu. 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T OK , 9 LANGUAGE (page 15) Select LANGUAGE to change the language used on menus or messages. L A N G UAG E ENGL I SH FRANÇA I S DEUTSCH ESPA ÑOL I TA L I ANO 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T 4 Close the menu. Press the MENU button once to return to normal viewing. If no buttons are pressed, the menu closes automatically after about 45 seconds. 0 Other menus (page 15) Set the following menu items. · RESET 0 · MENU LOCK RESET OK CANCEL MENU 1 2 8 0 x 1 0 2 4 / 6 0Hz EX I T x Resetting the adjustments You can reset the adjustments using the RESET menu. See page 15 for more information on resetting the adjustments. x Using the MENU, m/M, and OK buttons 1 Display the main menu. Press the MENU button to display the main menu on your screen. Adjusting the backlight (BACKLIGHT) If the screen is too bright, adjust the backlight and make the screen easier to see. Note The backlight cannot be adjusted when the MIDDLE, or LOW (page 10). mode is set to HIGH, GB MENU 1 Press the MENU button. The main menu appears on the screen. 2 Select the menu you want to adjust. Press the m/M buttons to display the desired menu. Press the OK button to select the menu item. 2 Press the m/M buttons to select (BACKLIGHT) and press the OK button. The BACKLIGHT menu appears on the screen. OK , 3 Press the m/M buttons to adjust the light level and press the OK button. 11 Adjusting the contrast (CONTRAST) Adjust the picture contrast. Note The contrast cannot be adjusted when the MIDDLE, or LOW (page 10). mode is set to HIGH, You can manually adjust the picture's sharpness (phase/pitch) and position (horizontal/vertical position). These adjustments are stored in memory and automatically recalled when the display receives the same input signal. These settings may have to be repeated if you change the input signal after reconnecting your computer. 1 Press the MENU button. The main menu appears on the screen. x Make further automatic adjustments to the picture quality for the current input signal (AUTO) 1 Press the MENU button. The main menu appears on the screen. 2 Press the m/M buttons to select 6 (CONTRAST) and press the OK button. The CONTRAST menu appears on the screen. 2 Press the m/M buttons to select press the OK button. The SCREEN menu appears on the screen. (SCREEN) and 3 Press the m/M buttons to adjust the contrast and press the OK button. Adjusting the black level of an image (BRIGHTNESS) Adjust the picture brightness (black level). Note The brightness cannot be adjusted when the MIDDLE, or LOW (page 10). mode is set to HIGH, 3 Press the m/M buttons to select AUTO and press the OK button. Make the appropriate adjustments of the screen's phase, pitch and horizontal/vertical position for the current input signal and store them. 4 Press the m/M buttons to select OK button. Return to the menu screen. and press the 1 Press the MENU button. The main menu appears on the screen. x Adjust the picture's sharpness manually (PHASE/PITCH) You can adjust the picture's sharpness as follows. 2 Press the m/M buttons to select 8 (BRIGHTNESS) and press the OK button. The BRIGHTNESS menu appears on the screen. 1 Set the resolution to 1280 × 1024 on the computer. 3 Start the CD-ROM, select the region and model, and display the test pattern. For Windows Click [Utility] t [Windows]/[Win Utility. exe]. For Macintosh Click [Utility] t [Mac]/[Mac Utility]. 3 Press the m/M buttons to adjust the brightness and press the OK button. Adjusting the picture's sharpness and centering (SCREEN) x Automatic picture quality adjustment function When the monitor receives an input signal, it automatically adjusts the picture's position and sharpness (phase/pitch), and ensures that a clear picture appears on the screen (page 16). Note While the automatic picture quality adjustment function is activated, only the 1 (power) switch will operate. 4 Press the MENU button. The main menu appears on the screen. 5 Press the m/M buttons to select press the OK button. The SCREEN menu appears on the screen. (SCREEN) and 6 Press the m/M buttons to select PHASE and press the OK button. [. . . ] · Adjust the picture position (page 13). Note that some video modes do not fill the screen to the edges. x Problems caused by a computer or other equipment connected, and not caused by the monitor · Set the resolution to 1280 × 1024 on your computer. · Adjust the brightness using the BRIGHTNESS menu (page 12). [. . . ]