Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual SONY SDX-700C. We hope that this SONY SDX-700C user guide will be useful to you.
Lastmanuals help download the user guide SONY SDX-700C.
Detailed instructions for use are in the User's Guide.
[. . . ] Make sure you read this manual before using the product. After reading this manual carefully, store it in a safe place. Microsoft, the logo of Microsoft and Windows NT are registered trademarks of the Microsoft Corporation in the United States and other countries. advanced Intelligent Tape is a trademark of the Sony Corporation. [. . . ] Always use the screws that are provided with this device. The screws that are provided with this device are metric screws (length: 5. Using screws that are longer than the screws that are provided with this device could result in damage to the device. If the power cord is damaged, immediately replace it with a new part of same type. do not repair the damaged section for reuse. Otherwise, the section repaired with vinyl tape or the like will be overheated to cause an electric shock or a fire. DC power cable (unused power supply connector in the computer) Except as noted below, use the SCSI cable provided with the Built-In AIT when connecting it to the N8103-56F SCSI controller. Further, do not use the provided SCSI cable with any controller other than the N8103-56F. â· If you are connecting the Built-In AIT to the N8103-56F SCSI controller during installation in the N8100-755F/-756F/-784F (Express5800/120Rd-2) or N8100-658AF/-667F (Express5800/ 120Rc-2), use the SCSI cable that is provided with these units rather than the one provided with the Built-In AIT. With these units, there is not enough space inside the cabinet to accommodate the cable provided with the Built-In AIT. â· Confirm the SCSI ID and other settings before installation. Make sure this ID is not used by any other device in the system. â· This unit does not have a built-in terminator. When connecting this unit to the last terminal of the SCSI bus terminal, attach a terminator to the end of the SCSI cable. 5 When the SCSI bus can be set on the side of the basic processing unit, set the following on the Set 160 Mbyte/second on basic processing units that support it, and to the next greatest transfer rate under 160 Mbyte/second on those that do not. When using the N8103-56F SCSI board, set to 160 Mbyte/second. Also, when the N8541-28F and N8141-28AF expansion units are connected, even if the transfer rate of the basic processing unit is 160 Mbyte/second, set it to the next greatest transfer rate under 160 Mbyte/second. Set the maximum transfer rates as follows according to the number of devices connected to the bus and the SCSI cable length. If you have other specifications at your disposal, use them over the ones below. Install the tape device driver only when you want to use the Windows 2000 Backup and Recovery Tools. The following explains how to handle the Built-In AIT. If you use a data cartridge of other manufacturer, a read/write error may occur. [. . . ] refer to the appropriate software documentation for details. S There may be a problem at a one or more of the following connections: SCSI cable, connector, the terminator, etc. If an error is indicated (ERRxx, for example), there may be a problem with the drive. S Cannot eject the data Internal s If the cartridge is not ejected even though the cartridge. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SONY SDX-700C
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual SONY SDX-700C will begin.
