User manual SONY SEL-50F18

[. . . ] Should you notice an abnormality in the unit, disconnect the main plug from the AC outlet immediately. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. Do not expose batteries or apparatus with battery-installed to excessive heat such as sunshine, fire or the like. The unit is not disconnected from the mains as long as it is connected to the AC outlet, even if the unit itself has been turned off. [. . . ] The unit can start or close a PARTY, and join or leave a PARTY. The unit can be detected by other devices on the home network. However, the unit cannot start or join a PARTY. Off ( : Factory setting) 57GB Changing the sound setting DSGX SOUND EFFECT SETTINGS Selecting a sound style You can select a sound style from five preset equalizer settings to match the genre of the music. M/m/ENTER Press SOUND EFFECT repeatedly. Each time you press the button, the sound style changes as follows. "Standard" ( ) t "Dynamic" t "Relax" t "Vivid" t "Live" t "Standard" t . . . ( : Factory setting) Generating a more dynamic sound (Dynamic Sound Generator X-tra) You can reinforce the bass and the treble to create a more powerful sound. This function is set to "DSGX On" as the factory setting. Turning the operating sound on or off The operating sound for the operation buttons on the main unit is set to "On" as the factory setting. You can turn this sound on or off. Press DSGX. Each time you press the button, the DSGX function switches between "DSGX On" and "DSGX Off. " 1 2 Press SETTINGS to enter the settings menu and select "Touch Key Settings" - "Beep Settings. " Select "On" ( ) or "Off. " ( : Factory setting) 58GB Using the timer TIMER ?/1 SLEEP VOLUME +/­ on the display. It keeps flashing until the unit enters the standby mode. You can change the function (sound source, such as the iPod & iPhone function, the Home Network function, etc. ) before the Sleep Timer turns the unit off. After the selected time elapses, the unit enters standby mode automatically. M/m/</, / ENTER To check the remaining time before the Sleep Timer turns the unit off Additional information Press SLEEP so that the remaining time before the Sleep Timer turns the unit off appears on the display. Tip Using the Sleep Timer You can set the Sleep Timer so that the unit enters standby mode automatically after a certain period of time (Sleep Timer function). This function operates even if the clock is not set. If you set both the Sleep Timer and Play Timer at the same time, the Sleep Timer takes priority. Note If you perform the following operations before the Sleep Timer turns the unit off, the Sleep Timer resets. · Enter the settings menu and perform "All Reset. " 1 2 Play the desired sound source. Press SLEEP repeatedly. Each time you press the button, the time interval changes as follows. You cannot go back to the previous display after the update starts. Formatting the system This function formats the unit and restores it to the condition it was at the time of purchase. Note that this process deletes all settings and information (e. g. , clock setting, network settings). 1 2 Press SETTINGS to enter the settings menu and select "All Reset. " Additional information When "Playback and network functions cannot be used during the setup. Press ENTER to continue. " appears, press ENTER. When " " is displayed, the message is continued to the next page. Press m to see the entire text string. 3 4 Select "OK. " When "Are you sure?" appears, select "OK. " Formatting starts. The unit automatically restarts at the end of the procedure. When the unit finishes formatting, the initial setup display appears. To cancel the procedure Select "Cancel" in step 3 or 4. To go back to the previous display Press BACK before you select "OK" in step 4. 63GB Troubleshooting Troubleshooting If a problem occurs while operating the unit, follow the steps described below before consulting your nearest Sony dealer. If an error message appears, it is recommended that you make a note of its contents for reference. If the on/standby indicator flashes in red or amber Immediately unplug the power cord, and check the following item. · Is the iPod/iPhone connector shortcircuited?After the on/standby indicator stops flashing, reconnect the power cord, and turn on the unit. If the issue persists, contact your nearest Sony dealer. 1 2 Check to see if the problem is listed in this "Troubleshooting" section. Check the following customer support site. · For customers in the USA: http://www. esupport. sony. com/ · For customers in Canada: English: http://www. sony. ca/ElectronicsSupport/ French: http://fr. sony. ca/ElectronicsSupport/ · For customers in Europe: http://support. sony-europe. com/ You will find the latest support information and a FAQ at this web site. Power The unit does not turn on. [. . . ] This product includes software developed by the University of California, Lawrence Berkeley Laboratory. This product includes software developed for the NetBSD Project by Wasabi Systems, Inc. This product includes software developed for the NetBSD Project by Matthias Drochner. 10. libcap Redistribution and use in source and binary forms of libcap, with or without modification, are permitted provided that the following conditions are met: 1. [. . . ]