User manual SONY SFM-1 INSTALLATION & CONNECTIONS

[. . . ] 12 Securing The Wall Plate To A Concrete Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Securing The Flat Panel To The Wall Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Lateral Shift Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Security Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] DO NOT LAY THE FLAT PANEL ON THE FLOOR WITHOUT ANY PROTECTION TO THE GLASS. AT LEAST (2) QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED FOR INSTALLATION OF THIS PRODUCT. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE TO THE FLAT PANEL. Once the flat panel is inverted, use a measuring tape to find the center of your flat panel measuring from outside to outside of the chassis (Figure 1). Using a pencil lightly mark the center of your flat panel (Figure 2). 1. 2. Top of Flat Panel Inverted Flat Panel Inverted Flat Panel Measuring Tape Bottom of Flat Panel C L Mark the Center of the Flat Panel C L Figure 1. Marking the Mount Mounting Bracket Positioning 1. Install the nylon spacers to the mounting points on the flat panel (Figure 3) Lay the left and right mounting brackets (stamped arrows facing out) (Figure 4). Page 6 Installation Manual SFM1 Nylon Spacers, If Applicable (See Chart) Inverted Flat Panel Center Mark Figure 3. Mounting Bracket Positioning Mounting Brackets Arrows Facing OUT Bottom of Flat Panel Figure 4. Mounting Bracket Installation Installation Manual Page 7 SFM1 NOTE: The mounting guides are designed with a center viewing guide on the side of them. There will be a "notch" cut on the side of the bracket (Figure 5). Mounting Bracket Bottom of Flat Panel Center of Flat Panel Center of Viewing Guide Figure 5. Locating the Center of the Flat Panel 3. Match the center of the viewing guide with the centerline you marked in Step 1 (Figure 6). C L Align the Mounting Brackets Bottom of the Flat Panel Figure 6. Adjusting the Mounting Brackets Page 8 Installation Manual SFM1 GriplatesTM 1. The GriplatesTM have M4, M5, M6 and M8 hole patterns to fit the hardware that the flat panel requires. Examples: If your display uses M8 x 20 Phillips head screws. Use the M8 mounting points (Figure 7). Dimples M8 M6 M5 M4 Figure 7. Once the mounting brackets are aligned, secure the GriplateTM to the flat panel. NOTE: The dimples of the top plates have to be facing up and the bottom dimples must be facing down. Use (1) GriplateTM per mounting point (Figure 8). [. . . ] At least (2) qualified personnel are strongly recommended for installation of this product. Failure to do so could result in serious injury and possible damage to the flat panel. Raise the flat panel with the LEFT and RIGHT mounting brackets secured to the flat panel and insert the top hooks from each bracket to the rod on the wall plate (Figure 15). Wall Plate TOP BOTTOM Figure 15. Securing the Flat Panel Lateral Shift Adjustment Make any lateral shift adjustment and lock it by tightening the two (2) ¼"-20 Phillips screws found on the bottom of the mounting brackets (Figure 16). [. . . ]