User manual SONY SL-VN71

[. . . ] 3-065-551-11 (1) Video Cassette Recorder Operating Instructions If you have any questions about this product, you may call: Sony Customer Information Services Center 1-800-222-SONY (7669) or write to: Sony Customer Information Services Center 6900-29 Daniels Parkway, PMB 330, Fort Myers, FL 33912 Declaration of Conformity Trade Name: SONY Model No. : SLV-N81/N71 Responsible Party: Sony Electronics Inc. Address: 1 Sony Drive, Park Ridge, NJ. 07656 USA Telephone No. : 201-930-6972 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. SLV-N81 SLV-N71 © 2001 Sony Corporation WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. · Do not install the unit near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock. · Do not install the unit in an inclined position. [. . . ] number you want by checking the channel number in the 3 Press OK. Notes · It takes about one hour to complete channel mapping. · The VCR can receive the program information signal only while the VCR is turned off and no timer recordings are set. · The VCR cannot set the guide channels correctly unless you enter the ZIP/POSTAL CODE in your area. · When you move to a different area, you must set up the VCR again and enter your new ZIP/ POSTAL CODE in the EASY SET UP procedure. continued Setting up the VCR Plus+® GOLD system (SLV-N81 only) 51 Setting up the VCR Plus+ GOLD system manually To set the guide channels, use the Channel Line-up Chart to check that the guide channel numbers match the TV channel your VCR receives. For example, if HBO is listed in the Channel Line-up Chart as channel 33, and your VCR receives HBO on channel 5, you need to coordinate these numbers using the following procedure. If the guide and TV channel numbers are the same, you can skip this procedure. 1 4 7 2 5 8 0 3 6 9 Number buttons, ENTER MENU M/m/</, OK 1 MENU Press MENU, then press M/m to highlight SETTINGS and press OK. SETTINGS TUNER PRESET SET VCR Plus+ sys. CH CABLE BOX CONTROL CLOCK SET LANGUAGE RETURN PLAY OK SELECT : SET : OK QUIT : MENU 2 PLAY OK Press M/m to highlight SET VCR Plus+ sys. CH, then press OK. SET VCR Plus+ sys. CH SMART CHANNEL MAPPING AUTO MANUAL SELECT : SET : OK QUIT : MENU 52 Setting up the VCR Plus+® GOLD system (SLV-N81 only) 3 PLAY OK Press M/m to highlight MANUAL, then press OK. SET VCR Plus+ sys. CH GUIDE CH ­­ ­ TV CH ­­ Getting Started SET GUIDE CH LIST QUIT : 0­9 : OK : MENU 4 1 4 7 2 5 8 0 3 6 9 Enter the guide channel number assigned in the program guide and press ENTER. SET VCR Plus+ sys. CH V C R W I GUIDE CH F O RTV CH LL LOOK CHANNEL MAPPING SIGNAL AFTER YOU 25 RN ­T OFF TU I 25 SET TV CH LIST QUIT : 0­9 ENTER : OK : MENU 5 1 4 7 2 5 8 0 3 6 9 · If you made Hookup 1, 3, or 4: Enter the actual number on your TV (and VCR) and press ENTER. SET VCR Plus+ sys. CH GUIDE CH 25 ­ TV CH 58 SET GUIDE CH LIST QUIT : 0­9 : OK : MENU · If you made Hookup 5: Enter the cable box output channel (usually 2, 3, or 4) and press ENTER. SET VCR Plus+ sys. CH GUIDE CH 25 ­ TV CH 3 SET GUIDE CH LIST QUIT : 0­9 : OK : MENU 6 7 PLAY OK Repeat steps 4 and 5 for each channel number that does not match. When you have set all channels, press OK to confirm your channel settings. To return to the previous page, press <. To go to the next page, press , . SET VCR Plus+ sys. CH LIST PAGE1 GUIDE TV 2­ 73 5­ 25 17 ­ 5 25 ­ 58 34 ­ 115 39 ­ 68 43 ­ 7 48 ­ 12 52 ­ 55 59 ­ 36 PAGE : QUIT : MENU GUIDE 66 68 71 74 79 82 85 88 91 93 TV ­ 48 ­ 59 ­ 63 ­ 123 ­ 6 ­ 100 ­ 98 ­ 52 ­ 30 ­ 87 continued Setting up the VCR Plus+® GOLD system (SLV-N81 only) 53 8 MENU After all settings are complete, press MENU to exit the menu. Tip · If you want to return to the previous menu, highlight RETURN and press OK. 54 Setting up the VCR Plus+® GOLD system (SLV-N81 only) Setting up the VCR Plus+® system (SLV-N71 only) How the VCR Plus+ system works Whenever you want to record a TV program, all you need to do is look up the "PlusCode" number, a number assigned to each program published in the TV section of most newspapers, cable TV listings, and even TV GUIDE magazine. Then, just enter the PlusCode number of the program you want and the VCR is automatically programmed to record that show. How to set up your VCR Setting up your VCR involves coordinating the TV channel number (the number you turn to on your TV or VCR to watch a program) with the guide channel (the number that's assigned to that channel in your program guide). To find the guide channel numbers, look at the "Channel Line-up Chart" in the program guide for your area that features VCR PlusCode numbers. It usually looks like the example to the right. To set the guide channels, use the Channel Line-up Chart to check that the guide channel numbers match the TV channel your VCR receives. [. . . ] see Editing E Easy Set Up 13, 16, 19, 22, 25 Editing 94 EP mode 63 F Favorite channel 88 S Safety tab 64 106 Index Quick reference to using the VCR Hookup 1 (SLV-N81 only) To play a tape 1 Set the TV to channel 3 or 4 (or to video input, if you made A/V connections). 2 Insert a tape and press H PLAY. To watch TV 1 Turn off the VCR, or press the VCR's TV/VIDEO button until the VIDEO indicator in the display window turns off. 2 Set the TV to the channel you want to watch. To record a program 1 Press VCR Plus+ on the remote commander. 3 Select ONCE, DAILY, or WEEKLY, then press ENTER. [. . . ]