User manual SONY SMOE511

[. . . ] Avoid the following conditions: · High humidity · High temperatures · Direct sunlight · Dust · Strong vibration · Wide temperature fluctuations Moving the drive Be sure to remove the disk cartridge when the drive is not being used. Also never move or transport the drive with the disk cartridge still inserted. If problems occur If any problems occur, turn off the power and unplug the drive, contact your dealer. 3-864-285-14(1) MO Disk Drive User's Guide To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. [. . . ] Refer servicing to qualified personnel only. CAUTION As the laser beam used in the SMOE511 series is harmful to the eyes, do not attempt to disassemble the unit. Refer servicing to qualified personnel only. The use of optical instruments with this product will increase eye hazard. The use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation. DANGER LASER RADIATION WHEN OPEN. DANGER RADIATIONS DU LASER EN CAS D'OUVERTURE. EVITER TOUTE EXPOSITION DIRECTE AU FAISCEAU. NICHT DEM STRAHL AUSSETZEN. Diese Ausrüstung erfüllt die Europäischen EMCBestimmungen für die Verwendung in folgender / folgenden Umgebung(en): · Wohngegenden · Gewerbegebiete · Leichtindustriegebiete (Diese Austüstung erfüllt die Bestimmungen der Norm EN55022, Klasse B. ) SMOE511 Series Printed in Japan Warning about Cleaning In the drive, preventive measures are taken to guard against dust. It is unnecessary to clean the optical lens of your drive. Diese Etiketten befinden sich an der Oberseite des Laufwerksgehäuses. Compatible Media The SMOE511 series is compatible with the following 5 1/ 4 inch (130 mm) Magneto Optical Disks. Model name SMOE511 series Compatibility Read Write ® ® ® ® ® ® ® ® ® ® ® ® ® ® ® ® ® ® ® ® ® ® ® ® ® × ® × ® × ® × ® × ® × ® × ® × ® ® ® ® ® ® ® ® ® × ® × ® × ® × ® ® ® ® ® ® ® ® ® ® ® ® ® ® ® ® Type 8× R/W 8× R/W 8× R/W 8× WO 8× WO 8× WO 4× R/W 4× R/W 4× WO 4× WO 4× DOW 4× DOW 2× R/W 2× R/W 2× WO 2× WO 1× R/W 1× R/W 1× WO 1× WO 2× R/W 2× R/W 2× WO 2× WO 1× R/W 1× R/W 1× WO 1× WO 2× R/W 2× R/W 2× WO 2× WO 1× R/W 1× R/W 1× WO 1× WO Description 5. 2GB 2048 4. 8GB 1024 4. 1GB 512 5. 2GB 2048 4. 8GB 1024 4. 1GB 512 2. 6GB 1024 2. 3GB 512 2. 6GB 1024 2. 3GB 512 2. 6GB 1024 2. 3GB 512 1. 3GB 1024 1. 2GB 512 1. 3GB 1024 1. 2GB 512 650MB 1024 594MB 512 650MB 1024 594MB 512 1. 3GB 1024 1. 2GB 512 1. 3GB 1024 1. 2GB 512 650MB 1024 594MB 512 650MB 1024 594MB 512 1. 3GB 1024 1. 2GB 512 1. 3GB 1024 1. 2GB 512 650MB 1024 594MB 512 650MB 1024 594MB 512 bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector bytes/sector ISO Standard ISO/IEC 15286 (working draft) Configuration and Location of Parts System Configuration The SMOE511 series is connected to a host computer through its SCSI interface. The maximum of seven peripheral devices can be linked as a daisy chain on the SCSI bus. Host Computer SCSI Cable Switch setting and Assignments Functional Switch Connector Pin Assignments A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 SCSI ID2 SCSI ID1 SCSI ID0 Disable SCSI Parity Disable Write Cache Disable Auto Spin-up Force Verify for Write command Disable Manual Eject Enable Fast SCSI Device Type Enable Termination Terminator Power B1 B2 B3 B4 B5* B6* B7* B8* B9* B10* B11 B12 GND GND GND GND Reserved Reserved Reserved Reserved Reserved Reserved GND Terminator Power Source SCSI Terminator The SMOE511 series features an internal SCSI bus terminator. When the drive is connected at the end of the SCSI chain, functional switch #11 (Enable Terminator) may be used to terminated the SCSI connection. For a single ended cable, 50-signal conductor flat cable or a 25-signal twisted cable can be used. The cable length shall not exceed six meters. Optional Switch Setting The SMOE511 series features Optional Switch S501 and S502. These two optional dip switches allow the user to set the drive configurations. ISO/IEC 14517 SMOE511 series SCSI peripheral devices System Configuration Example Location of Parts ISO/IEC 13549 SMOE511 * This pin is NOT directly connected to the GND. The SMOE511 series drives the signal to GND level depending on the functional switch setting. Otherwise, the signal is not driven to GND level. This section provides a general description of the SMOF551 series Magneto-Optical disk drive. [. . . ] Otherwise, the signal is not driven to GND level. This section provides a general description of the SMOF551 series Magneto-Optical disk drive. Front Panel Disk Insertion Slot SMOE511 -DD ISO/IEC 10089 ISO/IEC 11560 ISO/IEC 13549 WARNING: Write cache is enabled as default setting. The integrity of the buffer memory content is not guaranteed through power cycling. [. . . ]