User manual SONY SPP-AQ600

[. . . ] Follow all warnings and instructions marked on the product. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool. [. . . ] The corresponding line button lights up. "TALK" appears on the display and the display also shows the talk time in hours, minutes and seconds. "HANDSET IN USE" appears on the display of the base phone and the line button on the base phone double flashes in succession. (OFF) or replace the handset on the base phone. The display and the LINE 1 or LINE 2 button go off. 2 When you're done talking, press (FLASH/CALL WAITING) Receiving calls when the headset is connected When the TL-HD1 headset (not supplied) is connected to the I (HEADSET) jack, you can talk through the headset. Precaution Avoid listening your headset at so loud a volume that extended play might affect your hearing. Additional tasks To Adjust the handset volume Put a call on hold Do this Set the VOL switch to H (high), M (middle) or L (low). The LINE 1 or LINE 2 button will flash slowly. Press (LINE 1) or (LINE 2) to resume the conversation. Press (FLASH/CALL WAITING) again to return to the first caller. See "Turning off the ringer of the handset" on page 43. Switch to another call ("call waiting" service*) Turn on/off the ringer of the handset * You need to subscribe to the service from your telephone company. 30US Basics Note If another call comes in by "call waiting" service while conversing with an outside caller, you will hear two short beeps. Tip To inform you of an incoming call, the display shows "** RINGING **" when ringing. If you have subscribed to the Caller ID service; · the caller's number and/or name appears on the display when you receive a call (see page 52) or when another call comes in by "call waiting" service. Character table Key (1) (2) (3) (4) (5) (6) (7) (8) (9) (0) (*) (#) Character 1 AtB tCt2 DtEtFt3 GtHtI t4 J t K t Lt 5 M tNtO t6 PtQtRtS t7 TtUtVt8 W tX tY tZt9 0 * &t' t, t­ t. t# You will hear a confirmation beep. Press a dialing key until the desired character appears. (See the character table for details. ) Enter successive characters in the same way. To enter two characters assigned to the same key, or to enter a "space", press (VOLUME)(+) to move the cursor to the right. Example: to enter "SONY", press (7) four times (S), press (6) three times (O), press (VOLUME)(+) to move the cursor, press (6) twice (N), and press (9) three times (Y). SONY 34US Telephone Features 5 Press (PGM). "ENTER NUMBER" appears. 6 Enter the phone number. You can enter up to 32 digits, including a tone and a pause, each of which is counted as one digit. When the phone number of 17 digits or more has been entered , the phone number appears in two lines. SONY 1234567 1234567890123456 12 7 Press (PGM). You will hear a long confirmation beep, and the name and the number are stored. The display goes off. Note Do not allow more than 20 seconds to elapse between each step of the procedure. Tip If you have entered a wrong name or number in step 4 or 6, press (VOLUME)(--) to erase it. Then enter the correct name or number. Telephone Features To store a number to be dialed via Private Branch Exchange (PBX) Before entering a phone number in step 6 above, do as follows: 1 2 Enter the outside line access digit (e. g. , 9). Press (REDIAL/PAUSE). To change a stored number Store a new number, as described previously. continued Telephone Features 35US Speed dialing (continued) Making calls with speed dialing 1 2 3 Press (LINE 1) or (LINE 2) to select the line. Enter the desired speed dialing number ((0) to (9)). [. . . ] "PRIVATE" will appear on the display. · You have answered the call while "** RINGING **" was displayed. Be sure to answer after the Caller ID data is displayed. 68US Additional Information Caller ID Symptom The caller's name and/or phone number does not appear on the display during call waiting. You cannot dial the number from the Caller ID list. Remedy · Make sure you have subscribed to "Caller ID with call waiting" service (page 60). [. . . ]