User manual SONY SPP-S9101

[. . . ] Follow all warnings and instructions marked on the product. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool. [. . . ] To dial the number, press (SPEAKERPHONE) while the number is displayed. 34US Telephone Features Phone Directory You can dial a number by scrolling through the Phone Directory, in which up to 50 phone numbers can be stored. Storing phone numbers and names Example: to store "SONY" "123-4567". Turn Press 1 Press (PGM). (Be sure not to press (TALK). ) DIRECTORY AREA RINGER If "DIRECTORY" is not flashing, turn Jog Dial down to make it flash. Telephone Features 2 Press Jog Dial. "ENTER NAME" appears. (PAUSE) 3 Enter the name using the dialing keys. You can enter up to 16 characters. Press a dialing key until the desired character appears. (See the character table for details. ) Enter successive characters in the same way. To enter two characters assigned to the same key, or to enter a "space", turn Jog Dial up to move the cursor to the right. Example: to enter "SONY", press (7) four times (S), press (6) three times (O), turn Jog Dial up to move the cursor, press (6) twice (N), and press (9) three times (Y). Character table Key (1) (2) (3) (4) (5) (6) (7) (8) (9) (0) (*) (#) Character 1 AtBtCt2 DtEtFt3 GtHtIt4 JtKtLt5 MtNtOt6 PtQtRtSt7 TtUtVt8 WtXtYtZt9 0 * &t't, t­t. t# SONY continued Telephone Features 35US Phone Directory (continued) 4 Press (PGM). "ENTER NUMBER" appears. 5 Enter the phone number. You can enter up to 32 digits, including a tone and a pause, each of which is counted as one digit. When the phone number of 17 digits or more has been entered, the phone number appears in two lines. SONY 1234567 1234567890123456 12 6 Press (PGM). You will hear a long confirmation beep, and the name and the number are stored. The display goes off. Notes · If you intend to save a 51st phone number, you will hear five short error beeps and "MEMORY FULL" will be displayed. To store another phone number, erase one of the stored phone numbers (see page 38). · Do not allow more than 20 seconds to elapse between each step of the procedure. · The total number of phone numbers which can be stored into the Phone Directory varies according to the number of digits of each phone number. If all the phone numbers consist of up to 16 digits, you can store up to 50 phone numbers. You can continue talking to the caller through the speakerphone. Tips · While talking through the speakerphone on the base phone, if you pick up the handset, the call will be switched to the handset. · When the call is put on hold on the base phone, if you pick up the handset, the call will be switched to the handset. Telephone Features 41US Talking between the phones (Intercom) You can converse using the base phone and the handset. You can start the intercom from either phone. To talk from the handset to the base phone Press (INTERCOM) on the handset. (OFF) (TALK) (INTERCOM) After the base phone rings twice, you will be connected automatically. When a person at the base phone answers, you can talk with each other. "INTERCOM" appears on the display. When you are done talking or if no one answers the phone Press (OFF) on the handset. To talk from the base phone to the handset Press (INTERCOM) on the base phone. The base phone and handset ring and "** PAGING **" appears on the display. When a person at the handset presses (INTERCOM), you can talk with each other. "INTERCOM" appears on the display. (SPEAKERPHONE) (INTERCOM) When you are done talking or if no one answers the phone Press (INTERCOM) again. 42US Telephone Features Notes · If there's an incoming call while on the intercom, only the base phone rings. To answer the call, press (SPEAKERPHONE) on the base phone or (TALK) on the handset. [. . . ] "OUT OF AREA" will appear on the display. · The call was "blocked". "PRIVATE" will appear on the display. · You have answered the call while "** RINGING **" was displayed. [. . . ]