User manual SONY SPP-S9226

[. . . ] 3-222-919-11 (2) Cordless Telephone Operating Instructions US SPP-S9226 ©2000 Sony Corporation Owner's Record The model and the serial numbers are located at the bottom of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. ________________ 2US IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. [. . . ] · If you redial the same number repeatedly, this number will only be counted as one number of the total five registered numbers that can be redialed. · When dialing from a phone number with a registered name, that name will be displayed in the list in step 2. continued Basics 35US Making calls (continued) To store the dialed phone number into the Phone Directory 1 Display the name or phone number you want to store by doing steps 1 and 2 on page 35. 2 3 4 Turn Jog Dial to choose "PROGRAM", and then press Jog Dial. (If you're at the base phone, press Jog Button (ENTER). ) Enter the name by doing steps 4 and 5 on page 42. Turn Jog Dial to choose "[PGM]", and then press Jog Dial (or Jog Button (ENTER)). You hear a long confirmation beep, and the name and the number are stored. Note The dialed phone numbers of up to 20 digits can be stored in the Phone Directory. To erase the dialed phone number one by one 1 Display the name or phone number you want to erase by doing steps 1 and 2 on page 35. 2 3 Turn Jog Dial to choose "ERASE REDIAL", and then press Jog Dial. (If you're at the base phone, press Jog Button (ENTER). ) Turn Jog Dial to choose "YES", and then press Jog Dial (or Jog Button (ENTER)). You hear a long confirmation beep, and the number is erased. To erase the entire dialed phone numbers at once 1 Press (PROGRAM). 2 3 4 Turn Jog Dial to choose "MEMORY MANAGE", and then press Jog Dial. (If you're at the base phone, press Jog Button (ENTER). ) Turn Jog Dial to choose "ERASE ALL RDL", and then press Jog Dial (or Jog Button (ENTER)). Turn Jog Dial to choose "ERASE REDIAL", and then press Jog Dial (or Jog Button (ENTER)). You hear a long confirmation beep, and the entire number are erased. 36US Basics Receiving calls 1 When you hear the phone ring: · Press (TALK). or (CALL WAITING/FLASH) I(HEADSET) jack VOL switch · Pick up the cordless handset from the charger when the cordless handset is placed on the charger. (When Quick talk is set to "USE"; see page 38) "TALK" appears on the display and the display also shows the talk time in hours, minutes and seconds. "CORDLESS HANDSET IN USE" appears on the display of the base phone. Basics (HOLD) (PROGRAM) 2 When you're done talking, press (OFF) or replace the cordless handset on the charger. The display turns off. Receiving calls when the headset is connected When a headset (optional) is connected to the I (HEADSET) jack on the cordless handset, you can talk through the headset. Open continued Basics 37US Receiving calls (continued) Additional tasks To Adjust the cordless handset volume Put a call on hold Do this Set the VOL switch to H (high), M (middle) or L (low). "HOLD" appears on the display. Press (HOLD) again or pick up the cordless handset from the charger (When Quick talk is set to "USE"; see below) to resume the conversation. Press (CALL WAITING/FLASH) again to return to the first caller. Turn Jog Dial to choose "QUICK TALK", then press Jog Dial. Turn Jog Dial to choose "USE", then press Jog Dial. Switch to another call ("call waiting" service*) Receive a call by only picking up the cordless handset from the charger, without pressing (TALK)(Quick talk) * You need to subscribe to this service from your telephone company. Note If there is an incoming call during intercom conversation, intercom call will be disconnected, and both the base phone and the cordless handset will ring. Tip To inform you of an incoming call, the display shows "** RINGING **" even when you set the RING switch on the cordless handset to OFF. If you have subscribed to the Caller ID service; · the caller's number and/or name appears on the display when you receive a call (see page 57) or when another call comes in by "call waiting" service. [. . . ] Making calls Remedy · Make sure you have set up the base phone correctly (page 10). · Move the cordless handset closer to the base phone. · Make sure the telephone line cord is securely connected to the telephone outlet. · Make sure the battery is fully charged (page 13). [. . . ]