User manual SONY SPP-SS960

[. . . ] Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Do not use the telephone to report a gas leak in the vicinity of the leak. [. . . ] You hear a long confirmation beep, and the number is erased. To erase the entire dialed phone numbers at once 1 Press (PROGRAM). 2 3 4 Turn Jog Dial to choose "MEMORY MANAGE", and then press Jog Dial. (If you're at the base phone, press Jog Button (ENTER). ) Turn Jog Dial to choose "ERASE ALL RDL", and then press Jog Dial (or Jog Button (ENTER)). Turn Jog Dial to choose "ERASE REDIAL", and then press Jog Dial (or Jog Button (ENTER)). You hear a long confirmation beep, and the entire number are erased. 34US Basics Receiving calls 1 When you hear the phone ring: · Press (TALK). or (CALL WAITING/FLASH) I(HEADSET) jack VOL switch · Pick up the cordless handset from the charger when the cordless handset is placed on the charger. (When Quick talk is set to "USE"; see page 36) "TALK" appears on the display and the display also shows the talk time in hours, minutes and seconds. "CORDLESS HANDSET IN USE" appears on the display of the base phone. Basics (HOLD) (PROGRAM) 2 When you're done talking, press (OFF) or replace the cordless handset on the charger. The display turns off. Receiving calls when the headset is connected When a headset (optional) is connected to the I (HEADSET) jack on the cordless handset, you can talk through the headset. Open continued Basics 35US Receiving calls (continued) Additional tasks To Adjust the cordless handset volume Put a call on hold Do this Set the VOL switch to H (high), M (middle) or L (low). "HOLD" appears on the display. Press (HOLD) again or pick up the cordless handset from the charger (When Quick talk is set to "USE"; see below) to resume the conversation. Press (CALL WAITING/FLASH) again to return to the first caller. SAVER) (ERASE) ONE-TOUCH A ONE-TOUCH B ONE-TOUCH DIAL buttons ONE-TOUCH C 3 Turn Jog Dial to choose "ONETOUCH A" to "ONE-TOUCH C", and then press Jog Dial. continued Telephone Features 39US One-touch dialing (continued) 4 Enter the name by turning Jog Dial. You can enter up to 15 characters. Turn Jog Dial until the desired character is selected, and then press Jog Dial. ENTER NAME SONY_ ABCDEFGHIJKLMNOP QRSTUVWXYZ SWITCH NUMBER ENTER NAME Each press of Jog Dial after choosing "[SWITCH]" switches the characters from upper case letters t lower case letters t numbers and symbols. ENTER NAME ENTER NAME _ ABCDEFGHIJKLMNOP QRSTUVWXYZ SWITCH NUMBER _ abcdefghijklmnop qrstuvwxyz SWITCH NUMBER _ 0123456789"#$&'( )*+, -. /:; SWITCH NUMBER Enter successive characters in the same way. To enter a "space", turn Jog Dial to choose "[p]", and then press Jog Dial. 5 Turn Jog Dial to choose "[NUMBER]", and then SONY press Jog Dial. "ENTER NUMBERS" appears on the display. 6 Enter the phone number by turning Jog Dial. You can enter up to 20 digits, including a tone and a pause, each of which is counted as one digit. Turn Jog Dial until the desired number is selected, and then press Jog Dial. Icon Meaning Flash can be entered. If [VIP] has been selected, "9" will appear to the right of the displayed name. The ring type will change when calls are received from VIP registered numbers. ENTER NUMBERS _ 0123456789*# F P VIP PGM SONY 1234567_ 0123456789*# F P VIP PGM [F] [P] [VIP] SONY 1234567_ 0123456789*# F P VIP PGM 40US Telephone Features Enter successive numbers in the same way. When the phone number of 16 digits or more has been entered, the phone number appears in two lines. SONY 1234567890123456 12_ 0123456789*# F P VIP PGM 7 Turn Jog Dial to choose "[PGM]", and then press Jog Dial. You hear a long confirmation beep, and the name and the number are stored. The display goes off. Notes · Names cannot be entered using the dialing keys. · Do not allow more than 20 seconds to elapse during the operation procedure. Tips · When you select "[GO BACK]", you can return to the previous set display by pressing Jog Dial. [. . . ] · Make sure you have subscribed to "Caller ID with call waiting" service (page 64). · Make sure the "Caller ID with call waiting" service is set to "ACTIVE" (page 17). · Make sure nobody is talking with another phone on the same telephone line. · Make sure you entered your area code correctly (page 13). [. . . ]