User manual SONY SPP-110

[. . . ] Do not use the telephone to report a gas leak in the vicinity of the leak. Use only the power cord and batteries indicated in this manual. Check with local codes for possible special disposal instructions. Caution You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Privacy of communications may not be ensured when using this phone. Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] · When the talk time exceeds 9:59:59, the display counts from 0:00:00 again. If the battery becomes weak during a call The cordless handset will beep twice per second, "BATTERY LOW" appears on the display. Finish your call and replace the cordless handset on the charger to charge the battery pack. For optimum performance, charge the battery for a full 12 hours. Note that during the initial charge time (approx. 10 minutes), "PLEASE WAIT. . . " and "BATTERY LOW" appear on the display and the cordless handset cannot be used. After "BATTERY LOW" turns off, you may be able to use the cordless handset, but the battery duration will be very short; thus it is recommended that you fully charge the battery before next use. 34US Basics Making calls with the base phone 1 Pick up the handset or press (CALL WAITING/ FLASH) (SPEAKERPHONE) on the base phone. "TALK" or "SPEAKERPHONE" appears on the display and the display also shows the talk time in hours, minutes and seconds. When you're done talking, replace the handset in the cradle or press (SPEAKERPHONE) again. (REDIAL/PAUSE) (PROGRAM) (VOL +) (VOL -) Jog Dial 2 3 (ERASE) (EZ ACCESS) (*TONE) (HOLD) (SPEAKERPHONE) Basics To make a call after checking the phone number You can dial the phone number before picking up the handset or before pressing (SPEAKERPHONE). If you make a mistake when dialing the phone number, press (ERASE) to erase the number. Making calls using the EZ Access function To set up the access number, see "Setting up the EZ Access function" on page 23. 1 2 Dial the phone number (e. g. , 1-201-123-4567, or 011-. . . ). The system dials first, the access number set up with the EZ access function, and then the phone number you dialed in step 1. "SPEAKERPHONE" appears on the display. SPEAKERPHONE E12011234567 NEW OLD MASSAGE RING OFF 3 When you're done talking, or press (SPEAKERPHONE) again. Note If you have set up a phone number with the EZ access function, just press (EZ ACCESS) to dial the phone number (i. e. · When dialing from a phone number with a registered name, that name will be displayed in the list in step 2. continued Basics 37US Making calls (continued) To erase the dialed phone number one by one 1 Display the name or phone number you want to erase by doing steps 1 to 3 on page 37. 2 3 Turn Jog Dial to choose "ERASE REDIAL", and then press Jog Dial. Turn Jog Dial to choose "YES", and then press Jog Dial. You hear a long confirmation beep, and the number is erased. To erase the entire dialed phone numbers at once 1 Press (PGM). (Press (PROGRAM) on the base phone. ) 2 3 4 Turn Jog Dial to choose "MEMORY MANAGE", and then press Jog Dial. Turn Jog Dial to choose "ERASE ALL RDL", and then press Jog Dial. Turn Jog Dial to choose "ERASE REDIAL", and then press Jog Dial. You hear a long confirmation beep, and the entire number are erased. To store the dialed phone number into the Phone Directory See page 45. 38US Basics Receiving calls Receiving calls with the cordless handset 1 When you hear the phone ring: · Press (TALK). or I (HEADSET) jack VOL switch (HOLD) · Pick up the cordless handset from the charger when the cordless handset is placed on the charger. (When Quick talk is set to "ON"; see page 40) "TALK" appears on the display and the display also shows the talk time in hours, minutes and seconds. "HANDSET 1 IN USE" appears on the display of the base phone when the cordless handset with the station number "1" is in use. Basics (CALL WAITING/FLASH) (PGM) 2 When you're done talking, press (OFF) or replace the cordless handset on the charger. Receiving calls when the headset is connected When a headset (optional) is connected to the I (HEADSET) jack on the cordless handset, you can talk through the headset. Open continued Basics 39US Receiving calls (continued) Additional tasks To Adjust the cordless handset volume Put a call on hold Do this Set the VOL switch to H (high), M (middle) or L (low). [. . . ] "UNKNOWN NUMBER/ NAME/CALLER" will appear on the display. · The call was "blocked. " "BLOCKED NUMBER/ NAME/CALL" will appear on the display. · You have answered the call while "** RINGING **" was displayed. Please answer the call after the second ringer sound. [. . . ]