User manual SONY SPP-A700

[. . . ] Do not use the telephone to report a gas leak in the vicinity of the leak. Use only the power cord and batteries indicated in this manual. Check with local codes for possible special disposal instructions. Owner's Record The model and the serial numbers are located at the bottom of the unit. Record the serial number in the space provided below. [. . . ] The TALK/BATT LOW lamp goes off. 2 (* TONE) 4 3 4 (REDIAL/PAUSE) 1, 5 2 4 Microphone (CHANNEL/RINGER) 5 (REDIAL/PAUSE) Receiving calls 1 When you hear the phone ring; · Press (TALK) (or any key except (OFF)). or · Pick up the handset from the base unit when the handset is placed on the base unit. When you're done talking, replace the handset on the base unit or press (OFF). The TALK/BATT LOW lamp goes off. Note Do not allow more than 20 seconds to elapse between each step of the procedure. Tip If you enter a wrong number, press (PGM), then start from the beginning. To store a number to be dialed via Private Branch Exchange (PBX) Before entering a phone number in step 4, do as follows: 2 1 Enter the outside line access digit (e. g. , 9). 2 Press (REDIAL/PAUSE). To change a stored number Store a new number, as described previously. Note You can replace the stored number with a new number, but you cannot just erase it. Additional tasks To Adjust the handset volume Do this Set the VOL switch to H (high), M (middle) or L (low). Switch to tone Press (* TONE) after you're connected. dialing temporarily The line will remain in tone dialing until disconnected. Set the ringer type While the handset is not in use, press (CHANNEL/RINGER). Each press of (CHANNEL/RINGER) switches the ringer type by one of four type. Press the button again to get back to the first caller. Making calls with speed dialing 1 Press (TALK) and wait until the TALK/BATT LOW lamp lights up. 3 Enter the desired speed dialing number ((0) to (9)). The phone number stored in the speed dialing number will be dialed. Switch to another call ("call waiting service"*) * You need to subscribe to the service from your telephone company. Notes · Do not cover the microphone during the conversation; otherwise, the other party cannot hear your voice. Charge the battery pack for more than 12 hours. · Place the base unit away from noise sources. The handset does not ring when paging from the base unit. AC power adaptor 1 2 You hear a beep every three · Charge the battery pack for more than 12 hours. seconds and the TALK/ BATT LOW lamp flashes. · The battery pack may be discharged. Charge the battery pack for more than one minute. After this initial one minute, you may be able to use the handset, but more than 12 hours are necessary for full charging. Attach the telephone line cord and AC power adaptor cord to the base unit. Bundle the loose telephone line cord or AC power adaptor cord, if necessary. Plug the telephone line cord into the telephone outlet, and hook the base unit to the wall plate as illustrated. Plug the AC power adaptor to an AC outlet. Then raise the antenna so that it points towards the ceiling. Specifications General Operating frequency Frequency control Operation mode Operation channel Supplied accessories 902-928 MHz bands Crystal-controlled PLL FM, duplex 30 channels AC power adaptor AC-T127 Telephone line cord Rechargeable battery pack BP-T50 Rechargeable battery pack BP-T50 Standby: Approx. 2 1/4 × 7 1/8 × 1 15/16 inches (w/h/d), antenna excluded (approx. [. . . ] Si el equipo causa problemas en la línea, la compañía telefónica puede solicitarle que desconecte el equipo hasta que se resuelva el problema. Todas las reparaciones deberá realizarlas un centro de reparaciones Sony. Este equipo puede no utilizarse en el servicio de pago previo proporcionado por la compañía telefónica o la línea compartida. Para clientes en EE. UU. RECICLAJE DE PILAS DE NÍQUEL-CADMIO Las pilas de níquel-cadmio son reciclables. Puede ayudar a conserval el medio ambiente devolviendo las pilas que no desee al punto de recogida o de reciclaje más próximo. [. . . ]