User manual SONY SPP-M932

[. . . ] To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. If this equipment (SPP-M932) causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. [. . . ] Si experimenta algún problema con este equipo (SPP-M932), con respecto a la reparación o a la información sobre la garantía, póngase en contacto con Sony Direct Response Center: Tel 1-800-222-7669 (EE. Si el equipo causa problemas en la línea, la compañía telefónica puede solicitarle que desconecte el equipo hasta que se resuelva el problema. Todas las reparaciones deberá realizarlas un centro de reparaciones Sony. Este equipo puede no utilizarse en el servicio de pago previo proporcionado por la compañía telefónica o la línea compartida. Este equipo es compatible con dispositivos para ayuda a la audición. Cuando programe números de emergencia y (o) realice llamadas de prueba a los mismos: 1. Permanezca poco tiempo en la línea y explique a la otra parte la razón de la llamada. Realice tales actividades en horas no punta, como por la mañana temprano o a últimas horas de la tarde. La operación está sometida a las dos condiciones siguientes: (1) Este dispositivo puede no causar interferencia, y (2) Este dispositivo deberá aceptar cualquier interferencia, incluyendo la que pueda causar una operación indeseada. 2 4 Set the correct month using the Jog lever, then press (SELECT). 1 Press (PGM). 2 Display "SET ONE TOUCH" using the Jog lever. 5 Set the correct day, hour (1 to 12) and minute (00 to 59) as in step 4. (TALK) 3 Press (SELECT). Modular 6 Choose "AM" or "PM" using the Jog lever, then press (PGM). You will hear a long confirmation beep and the phone starts counting time. If a number is stored, it appears on the display. The cursor flashes at the last digit of the phone number. To store a number to be dialed via Private Branch Exchange (PBX) Before entering a phone number in step 4 above, do as follows: SMITH (OFF) or replace the handset on the base unit. The display and the LINE lamp on the base unit go off. 1 2 Enter the outside line access digit (e. g. , 9). Press (REDIAL/PAUSE). 6 Lower the Jog lever to erase the number and enter the new number. If you don't want to change the number, skip this step. Making calls with one-touch dialing Receiving calls 1 When you hear the phone ring, pick up the handset from the base unit, and press (TALK). "TALK" appears on the display. The LINE lamp on the base unit lights up. 1 2 Press (TALK) and wait until "TALK" appears on the display. The phone number stored on the one-touch dialing button will appear on the display and will be dialed. 7 Press (SELECT). You will hear a long confirmation beep and the name and/or the number is changed. (continued) Erasing a memory location 1 Display the name and phone number you want to erase by doing steps 1 and 2 in "Making calls from the Phone Directory" below. Press (SELECT). Locating the handset SONY You can page the handset from the base unit. Note that you cannot page if the handset is in use. To erase the entire list at once You can erase the entire list at once only when all the data has become "OLD" data. If there is any "NEW" data, you cannot erase the entire list. When you receive the 10 digits phone number Mounting the base unit on a wall 1 2 Telephone line cord Troubleshooting If you've experienced any of the following difficulties while using your phone, use this troubleshooting guide to help you remedy the problem. [. . . ] · If you do not use the handset for a long period of time, remove the battery pack after charging for more than 10 hours. This maintains battery life. Handset Power source Battery life Dimensions Rechargeable battery pack BP-T18 Standby: Approx. 2 1/4 x 1 7/8 x 7 1/4 inches (w/h/d), antenna excluded (approx. 220 g), battery included 1 2 3 Perform steps 1 to 3 in "Setting the ringer type". [. . . ]