User manual SONY SPP-N1020

[. . . ] 3-230-539-12(1) Cordless Telephone Operating Instructions 4. The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of the REN's should not exceed five (5. 0). [. . . ] Realice tales actividades en horas no punta, como por la mañana temprano o a últimas horas de la tarde. La operación está sometida a las dos condiciones siguientes: (1) Este dispositivo puede no causar interferencia, y (2) Este dispositivo deberá aceptar cualquier interferencia, incluyendo la que pueda causar una operación indeseada. 2 4 Set the correct month using the Jog lever, then press (SELECT). 1 Press (PGM). 2 Display "SET ONE TOUCH" using the Jog lever. 5 Set the correct day, hour (1 to 12) and minute (00 to 59) as in step 4. (TALK) 3 Press (SELECT). Modular 6 Choose "AM" or "PM" using the Jog lever, then press (PGM). You will hear a long confirmation beep and the phone starts counting time. If a number is stored, it appears on the display. To store a new number, lower the Jog lever several times to erase it. To store a number to be dialed via Private Branch Exchange (PBX) Before entering a phone number in step 5 above, do as follows: SET ONE TOUCH 1 2 Enter the outside line access digit (e. g. , 9). Press (REDIAL/PAUSE). Changing a stored name and/or phone number Prepare the battery pack Charge the battery pack for more than 12 hours before you start using your phone. Tip You may press (SELECT) instead of pressing (PGM) in step 6. 4 Enter the phone number. (ONE TOUCH) (REDIAL/PAUSE) 1 1 2 BP-T18 Black 3 4 Making and receiving calls Making calls You can enter up to 16 digits, including a tone and a pause, each of which is counted as one digit. Display the name and phone number you want to change by doing steps 1 and 2 in "Making calls from the Phone Directory" on the reverse. Press (SELECT). SONY 2 DIAL EDIT ERASE 1 Pick up the handset from the base Red CHARGE lamp 5 Press (PGM). unit. 1 Slide open the battery compartment lid of the handset. 2 Connect the battery connector with correct polarity (black wire goes on right side and red wire goes on left). 2 Press (TALK) and wait until "TALK" (HOLD) You will hear a long confirmation beep, and the number is stored. The display goes off. 3 Make "EDIT" flash using the Jog lever, then press (SELECT). The cursor flashes at the last character of the name. SONY appears on the display. You will then hear a dial tone. The LINE lamp on the base unit lights up. If "NO CONNECT" appears on the display, move closer to the base unit. Note Do not allow more than 20 seconds to elapse between each step of the procedure. Tips · You may press (ONE TOUCH) instead of doing steps 2 and 3. · The entered phone number (*) and (#) are displayed as " " and " " respectively in step 4. · You may press (SELECT) instead of doing step 5. 4 Lower the Jog lever to erase the characters and enter the new name. If you want to change only the number, skip this step. 3 Insert the battery pack, and close the lid. 4 Place the handset on the base unit. The CHARGE lamp lights up when the handset is properly seated on the charge terminals of the base unit. Charge the battery pack for more than 12 hours so that the battery is fully charged. The CHARGE lamp remains lit even after charging is completed. Battery duration A fully charged battery pack lasts for about: · approx. 7 hours when you use the handset continuously. 7 days when the handset is in standby mode. Notes · The battery pack will gradually discharge over a long period of time, even when not in use. [. . . ] Select "OFF" using the Jog lever. You will hear a long confirmation beep. RINGER: OFF Erasing data from the Caller ID list Old data will be erased automatically when a 51st call comes in, but you can also manually erase unnecessary data one by one or erase the entire list. VOICE MAIL lamp Mass 5 Press (SELECT) again. You will hear a long confirmation beep and the name and number are stored. Note You cannot use this feature, if you have not subscribed to your telephone company's message service. For details on the availability of this service, please ask your telephone company. Base unit Power source Battery charging time Dimensions DC 9V from AC power adaptor AC-T130 Approx. [. . . ]