User manual SONY SPP-S2430

[. . . ] 3-225-952-11 (1) Cordless Telephone Operating Instructions US SPP-S2430 ©2000 Sony Corporation Owner's Record The model and the serial numbers are located at the bottom of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. ________________ IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. [. . . ] The display turns off. Receiving calls when the headset is connected When a headset (optional) is connected to the I (HEADSET) jack on the cordless handset, you can talk through the headset. Open continued Basics 35US Receiving calls (continued) Additional tasks To Adjust the cordless handset volume Put a call on hold Do this Set the VOL switch to H (high), M (middle) or L (low). "HOLD" appears on the display. Press (HOLD) again or pick up the cordless handset from the charger (When Quick talk is set to "USE"; see below) to resume the conversation. Press (CALL WAITING/FLASH) again to return to the first caller. Turn Jog Dial to choose "QUICK TALK", then press Jog Dial. Turn Jog Dial to choose "USE", then press Jog Dial. Switch to another call ("call waiting" service*) Receive a call by only picking up the cordless handset from the charger, without pressing (TALK)(Quick talk) * You need to subscribe to this service from your telephone company. Note If there is an incoming call during intercom conversation, intercom call will be disconnected, and both the base phone and the cordless handset will ring. Tip To inform you of an incoming call, the display shows "** RINGING **" even when you set the RING switch on the cordless handset to OFF. If you have subscribed to the Caller ID service; · the caller's number and/or name appears on the display when you receive a call (see page 55) or when another call comes in by "call waiting" service. · the name stored in the one-touch dialing or Phone Directory appears on the display if the call matches the number stored on ONE-TOUCH DIAL buttons or in the Phone Directory (memory match function; see page 55). · the ringer sound changes to a higher tone if the call matches the number VIP stored on ONE-TOUCH DIAL buttons or in the Phone Directory (memory match function; see page 55). To turn the ringer off Set the RING switch on the bottom to OFF. "[RINGER OFF]" appears on the display. You can still make calls, and also receive calls if another telephone connected to the same line rings to inform you on incoming calls. You can also receive an intercom call. RING switch 36US Basics Receiving calls with the base phone When you hear the phone ring, pick up the handset or press (SPEAKERPHONE) on the base phone. "TALK" or "SPEAKERPHONE" appears on the display and the display also shows the talk time in hours, minutes and seconds. When you're done talking, replace the handset in the cradle or press (SPEAKERPHONE) again. To obtain the best speakerphone performance, see page 32. (SPEAKERPHONE) (HOLD) (CALL WAITING/ FLASH) (VOLUME) Basics Additional tasks To Adjust the handset or speakerphone volume Do this During phone conversation, press (VOLUME)(+) or (-). There are 3 steps for the handset volume level, and 7 steps for the speakerphone volume level. "HOLD" appears on the display. Press (HOLD), (SPEAKERPHONE), or pick up the handset from the base phone to resume the conversation. Press (CALL WAITING/ FLASH) again to return to the first caller. The ringer volume can be adjusted to three different levels: high, low, and "OFF". [. . . ] · You may need to change the number of digits of the phone number (page 62). · This function may not work when the phone is connected to a Private Branch Exchange (PBX). · If the call is from an office which uses multiple lines, the phone number may not match the number you put in the memory. · If you have stored phone number with an outside line access digit on a one-touch dial or in the Phone Directory because the phone is connected to a Private Branch Exchange (PBX), the phone number will not match the Caller ID data. [. . . ]