User manual SONY SRP-L210

[. . . ] A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. [. . . ] · The TRIM controls treat their adjustable signal range as two areas (one is between ­60 dBu and ­50 dBu and another is between ­49 dBu and ­30 dBu) and because of this, sound dropouts may be observed while adjusting the reference level for the signal input from the microphones. (reference level) indicators: Light up yellow when the audio signal whose level exceeds the reference level is input to the MIC INPUT 1 to 4 connectors. While the audio signal is input, adjust the TRIM Location and Function of Parts 11 Rear panel 1 23 4 5 1 6 7 3 # 3 # 3 3 # # 3 # qf qd qs qa 0 9 8 A ANT IN a/b connectors (BNC type) Connect antennas for the tuner unit installed in the SRP-L210. Only the supplied antennas or the UHF Antenna AN-820 (not supplied) can be used. Notes B PROJECTOR CONTROL CONTROL S IN/OUT connectors (stereo mini jack) Used to control the LCD Data Projector VPL-PX15 exclusively. For details on the function of this connector, see "PROJECTOR CONTROL CONTROL S IN/OUT connectors" (page 24). C PROJECTOR CONTROL RS-232C connector (Dsub, 9-pin, male) Used for the control of a projector or display monitor with an RS-232C connector connected to the F OUTPUT COMPONENT/RGB or OUTPUT VIDEO connector of the SRP-L210. D REMOTE PARALLEL connector (D-sub, 25-pin, female) This connector consists of 10 input pins and 10 output pins. The SRP-L210 can be controlled by a switch or volume controller connected to the input pins. Connecting these pins to an emergency broadcast system allows the SRP-L210's audio output to be cut off during an emergency broadcast. An LED can be connected to the output pins to indicate the unit's status. The following devices can be connected to this connector. · If the antenna is not installed correctly, faulty reception may result, including intermittent sound. H CIRCUIT BREAKER button The circuit breaker cuts off the main power when excessive current flows through the AC IN connector. If the circuit breaker trips, press the CIRCUIT BREAKER button to reset the breaker, but do not use the SRP-L210. Instead, turn it off and contact the Sony dealer from whom you purchased the unit. I AC IN connector Connects the supplied AC power cord. J LINE OUTPUT connectors (1 to 4) (phono jack) Connect to the line input connectors of a power amplifier, CD/MD recorder, etc. The LINE OUTPUT 3/4 connectors are factory-set to function as the REC OUT connectors. Location and Function of Parts 13 Installation Installing the tuner units Up to two WRU-806 UHF Synthesizer Tuner Units (not supplied) or two URX-M1 Tuner Units included in the UWP-X1/X2 (not supplied) can be installed in the SRP-L210. Notes that of the tuner unit, or that the battery in the microphone is running down. To remove the tuner unit Pull the latch securing the tuner unit to the side and pull out the tuner unit. Tuner unit · To prevent the production of noise, be sure to turn the SRP-L210 off before installing or removing the tuner units. · When installing the tuner unit, insert it fully into the tuner slot of the SRP-L210 and secure it with the latch on the slot. · Do not touch the inside of the tuner unit slots. Latch 1 Turn off the SRP-L210, check the top and bottom sides of the tuner unit, and then insert it into the slot. Tuner unit About blank panels Two blank panels (large and small) are attached to the front of the SRP-L210. Remove both of these panels to perform settings. After completing the settings, reattach the panels to prevent malfunctioning of the unit and to keep the tuner units from falling off the slot. When the input level controls are used Latch 2 Turn on the SRP-L210 and perform the group and channel settings for the tuner unit, following the instructions in "WRU-806 channel setting" (page 15). [. . . ] · ROUTING settings are incorrect. t Use the SRP-L210 Manager to set the routing correctly. · The SYSTEM TYPE selector setting is incorrect. t Make correct settings. No microphone sound is output. [. . . ]