User manual SONY SRSD4100

[. . . ] 3-264-410-11(1) C PC, CD or MD Walkman, etc. Installing the satellite speakers (See fig. A) Use the supplied screws to attach the base to the satellite speaker. The satellite speaker can be used either placed on a desk or attached to a wall. Troubleshooting Should you encounter a problem with your speaker system, check the following list and take the indicated measures. If the problem persists, consult your nearest Sony dealer. Active Speaker System Rear speaker (Left) There is no sound from the speaker system. · Make sure all the connections have been correctly made. [. . . ] The connecting cord is not supplied with this system. NOTICE FOR THE CUSTOMERS IN THE USA Design and specifications are subject to change without notice. Note First, be sure to apply a bond (anaerobic threadlocking material) to the hollow wall anchor to prevent the screw loosening. , 5 mm 7 mm ø 4 mm This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. On placement · Do not set the speakers in an inclined position. · Do not leave the system in a location near heat sources, or in a place subject to direct sunlight, excessive dust, moisture, rain or mechanical shock. · Do not install the satellite speaker anywhere other than on a wall. · Do not hang on the satellite speaker or hang anything on it. Note To switch INPUT1 and INPUT2, use ON/OFF of the device connected to the control box. Note 9. 5 mm or more Do not hang on the satellite speaker or hang anything on it. 4 5 Connect the subwoofer to the wall outlet. C) On cleaning Do not use alcohol, benzene, or thinner to clean the cabinet. If you have any questions or problems concerning your speaker system, please consult your nearest Sony dealer. B Connecting cord (not supplied) to INPUT2 jack to 8-pin Din jack Control Box (rear) to LINE OUT or headphones jack (stereo mini-jack) CD/MD Walkman*, etc Precautions On safety The nameplate indicating operating voltage, power consumption, etc. , is located on the rear exterior. · Before operating the system, be sure that the operating voltage of the system is identical with that of your local power supply. Where purchased Operating voltage 120 V AC, 60 Hz 220 ­ 230 V AC, 50 Hz · 110 ­ 120 V AC, 50/60 Hz · 220 ­ 230 V AC, 50 Hz U. S. A. /Canada European countries Other countries FRONT REAR Listening to the sound (See fig. D) First, turn down the volume on the control box. The volume should be set to minimum before you begin playing the programme source. to INPUT1 jack (Green to front and Black to rear channel) 1 2 Set the POWER switch to ON on the control box. The POWER indicator lights up. Satellite speaker (rear) Connecting Cable (for 4 channel signal input) (supplied) to LINE OUT jack (Green to front and Black to rear channel) Adjust the VOLUME control on the control box. You can adjust the volume of the subwoofer and each satellite speaker. When connecting to the headphone output, also adjust the volume of the connected component. After listening, set the POWER switch to OFF. BASS: Ajusta el nivel de graves (altavoz potenciador de graves) REAR: Ajusta el sonido envolvente posterior (altavoz posterior) PHONE: Toma para conectar los auriculares. En este caso, sólo serán útiles las señales del canal L/ R frontal. No podrá utilizar el control de volumen BASS o REAR. A A Base DUAL STEREO: Cambia de una fuente de 2 canales a una de 4. Ajuste el interruptor en ON cuando escuche una fuente de 2 canales desde un PC, Walkman, etc. , conectado a este sistema. Ajuste el interruptor en OFF cuando escuche una fuente de 4 canales desde un PC o tarjeta de sonido conectados a este sistema. Se emite sonido envolvente de 4 canales. En este caso, los altavoces traseros no funcionarán con fuentes de 2 canales. Para más detalles sobre la configuración de las tarjetas de sonido, consulte el manual de instrucciones de la tarjeta de sonido. 3 Conecte el cuadro de controles al equipo fuente. ­ Salida de la tarjeta o dispositivo de sonido: Conecte las tomas INPUT1 (altavoz frontal y posterior) del cuadro de controles y las tomas de la tarjeta de sonido con el cable de conexión suministrado. Para obtener más información, consulte el manual de instrucciones de la tarjeta de sonido. [. . . ] · Compruebe si los auriculares están conectados. Si es así, desconéctelos. 2 Asegúrese de fijar los tornillos correctamente. Apriete el tornillo con el dedo. Si le resulta complicado, utilice un destornillador para fijarlo. 3 Fije el anclaje de pared hueca en la pared. Notas · Compruebe que el grosor de la pared es el adecuado. [. . . ]