User manual SONY SRW5000 INSTALLATION MANUAL

[. . . ] HD DIGITAL VIDEOCASSETTE RECORDER SRW-5000 INSTALLATION MANUAL 1st Edition Serial No. WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! [. . . ] If unnecessary screws are fastened, rack mounting will be unenabled. B4 x 6 Inner rail Inner rail B4 x 6 SRW-5000 1-5 . Remove the four screws from both sides (left and right) of the unit. . Slide the intermediate rail as shown in the figure, and then loosely attach the rail bracket to the outer rail with a plate nut (large) and the two screws. B4 x 6 Plate nut (large) Rail bracket Outer rail Slide B4 x 8 Intermediate rail B4 x 6 n Keep these screws (B4 x 6). Be sure to use these screws when directly fixing the side panels without the rack angles. The use of longer screws such as the screws (PSW 4 x 16) for fixing the rack angles will cause a malfunction of the unit. Attach the two rack angles to both sides (left and right) of the unit with the four screws (PSW4 x 16) supplied with the rack mount kit. Tightening torque: 120 x 10 _2 N. m {12. 2 kgf. cm} 11. Slide the ball retainer in the direction of the arrow, and then loosely attach the rail bracket to the outer rail with a plate nut (large) and the two screws. Outer rail Plate nut (large) Rail bracket Slide Intermediate rail Ball retainer B4 x 8 PSW4 x 16 Rack angle PSW4 x 16 Rack angle PSW4 x 16 1-6 SRW-5000 . Loosely attach the two outer rails to the middle of the 5U space in the rack for mounting this unit, with the eight hexagon socket head cap screws, eight flat washers, and four plate nuts (small). 13. Check that the two intermediate rails attached to the rack are parallel. Hexagon socket head cap screw 2 pcs A Hexagon socket head cap screw 2 pcs Rear side Plate nut (small) Rail bracket fixing screws By 5U Rail Flat washer Hexagon socket head cap screw Intermediate rails Rail bracket fixing screws 2U L-shaped hexagon wrench Front side A' Hexagon socket head cap screw 2 pcs A = A' = 416 mm Hexagon socket head cap screw 2 pcs 14. As shown in the following figure, adjust each frontside position of the outer rails on both sides (left and right) so that the distance from the surface of the rack to the tip of the rail becomes within the range of 50 to 55 millimeters. To fix the four rail brackets, fully tighten the eight loosely fitted rail bracket fixing screws (B4 x 8) in steps 11 and 12. Tightening torque: 120 x 10 _2 N. m {12. 2 kgf. cm} Rack Rail bracket Outer rail 50 to 55 mm Rack angle Rail bracket fixing screws B4 x 8 SRW-5000 16. To fix the two outer rails to the rack, fully tighten the eight loosely fitted hexagon socket head cap screws in step 12 using the L-shaped hexagon wrench. Mounting in rack c Be sure to carry the unit by the two persons or more. Set each ball retainer to the position as shown in the figure in the direction of the arrow. Front side 21. Slide the unit in and out from the rack about three times and check that the slide rails move smoothly. If they are not smoothly, demount the unit and go back to "Attaching the outer rails" (step 12). c When demounting the unit, carry it by the two persons or more. n This unit does not have the feet at this operating. Put down the unit on the floor or other, being careful not to damage the unit. Push the unit in the depths of the rack. [. . . ] Pull the ME wire for a few times with short steps to take up the tape inside the cassette. Be careful for the tape not to catch in parts such as a flange of a tape guide. Don't take the ME wire off the wire holder. The ME wire links with the T real table. [. . . ]