User manual SONY SS-SR195

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­ Reorient or relocate the receiving antenna. [. . . ] ­ folder levels (the tree structure of files) is eight. · Compatibility with all MP3 encoding/writing software, recording device, and recording media cannot be guaranteed. Incompatible MP3 discs may produce noise or interrupted audio or may not play at all. Right speaker (Low freq. ) Solid (Red/) Solid (Black/) Left speaker (High freq. ) Selecting a music source Press the following buttons (or press FUNCTION repeatedly). To select Press CD on the remote. Using optional audio components To connect an optional headphones Connect headphones to the PHONES jack on the unit. CD Right speaker (High freq. ) Tuner TUNER/BAND . FUNCTION repeatedly until "AUDIO IN" appears. Speakers Tape Component* (connected using an audio cord) To connect an optional component Connect additional audio source components to the AUDIO IN jack on the unit using an audio analog cord (not supplied). Turn down the volume on the system, and then select the AUDIO IN function. Attach the supplied speaker pads to the bottom of the speakers to prevent slipping. Power Connect the power cord to a wall socket. * If the component has the AVLS (Automatic Volume Limiter System) or BASS BOOST function, turn off the function to avoid distorted sound from the speakers. Wall socket Other Operations Creating your own CD program (Program Play) Use buttons on the remote to create your own program. Troubleshooting Recording onto a tape Use a TYPE I (normal) tape only. You can record just the portions you like from a sound source, including connected audio components. Use buttons on the unit to control tape recording. Messages CANNOT LOCK : The system cannot be locked after you have done the procedure of "When carrying this system. " COMPLETE : The preset operation ended normally. FULL : You tried to program more than 15 tracks (steps). NO DISC : There is no disc in the player, or you have loaded a disc that cannot be played. NO STEP : All of the programed tracks have been erased. NOT IN USE : You pressed an invalid button. If you use both timers, the Sleep Timer has priority. · Remove any obstacles between the remote and the remote sensor on the unit, and position the unit away from fluorescent lights. · Point the remote at the system's sensor. · Move the remote closer to the system. Discs that this system CANNOT play · CD-ROM · CD-R/CD-RW other than those recorded in music CD format or MP3 format conforming to ISO9660 Level 1/Level 2, Joliet or multisession · CD-R/CD-RW recorded in multisession that have not ended by "closing the session" · CD-R/CD-RW of poor recording quality, CD-R/CD-RW that have scratches or are dirty, or CD-R/CD-RW recorded with an incompatible recording device · CD-R/CD-RW which is finalized incorrectly · Discs containing files other than MPEG 1 Audio Layer3 (MP3) files · Discs of non-standard shape (for example, heart, square, star) · Discs that have adhesive tape, paper, or sticker attached to them · Rental or used discs with attached seals where the glue extends beyond the seal · Discs that have labels printed using ink that feels tacky when touched Specifications Main unit AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: (The United States model only) With 8 ohm loads, both channels driven, from 150 ­ 10, 000 Hz; rated 80 watts per channel minimum RMS power, with no more than 10% total harmonic distortion from 250 milliwatts to rated output. Sleep Timer: You can fall asleep to music. This function works even if the clock is not set. If you select "AUTO, " the system automatically turns off after the current disc or tape stops or in 100 minutes. If the tape deck is still playing or recording at the set time, the system turns off after the tape deck stops. CD/MP3 player The sound skips, or the disc will not play. · Wipe the disc clean, and replace it. · Move the system to a location away from vibration (for example, on top of a stable stand). · Move the speakers away from the system, or place them on separate stands. At high volume, speaker vibration may cause the sound to skip. Presetting radio stations You can preset your favorite radio stations and tune them in instantly by selecting the corresponding preset number. Use buttons on the remote to preset stations. Amplifier section 1 Press TUNER/BAND repeatedly to select "FM" or "AM. " Play Timer: You can wake up to CD or tuner at a preset time. Use buttons on the remote to control the Play Timer. [. . . ] To change the setting, start over from step1. Tip The Play Timer setting remains as long as the setting is not canceled manually. Tape deck The sound exhibits excessive wow or flutter or dropout. · Clean the capstans and pinch rollers. Also, clean and demagnetize the tape heads. See "Precautions" for details. On placement · Do not place the system in an inclined position or in locations that are extremely hot, cold, dusty, dirty, or humid or lacking adequate ventilation, or subject to vibration, direct sunlight or a bright light. · Be careful when placing the unit or speakers on surfaces that have been specially treated (for example, with wax, oil, polish) as staining or discoloration of the surface may result. [. . . ]