User manual SONY STP-WS2 DATASHEET

[. . . ] Refer servicing to qualified personnel only. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. The shielded interface cable recommended in this manual must be used with this equipment in order to comply with limits for a digital device pursuant to Subpart B of Part 15 FCC Rules. INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] · The DISC 1 ­ 5 indicators light up in the display when CD is loaded on the tray. · If a CD is not loaded to any of DISC 1 ­ 5, "NO DISC" appears. · If you press a number button on the remote, the track corresponding to the pressed number on the current disc starts playing (Track Direct Play). Listening to the radio Preset radio stations in the tuner's memory first (see page 10). To turn on the power, press ?/1. ?/1 (power) VOLUME +/­ TUNER/BAND ­/+ ?/1 (power) 1 2 3 2 STEREO/ MONO + 4 5 8 6 7 9 10/0 >10 VOL +/­ N X x ­ 1 ­ + . > M m + ­ 3 14 1 Press TUNER BAND repeatedly until the band you want appears. Each time you press the button, the band changes as follows: FM y AM To listen to non-preset radio stations · Press PLAY/TUNING MODE repeatedly until "MANUAL" appears in step 2, then press TUNER + or ­ repeatedly to tune in the desired station (Manual Tuning). · Press PLAY/TUNING MODE repeatedly until "AUTO" appears in step 2, then press TUNER + or ­. The frequency indication changes and scanning stops when the system tunes in a station (Automatic Tuning). Basic Operations 2 Press PLAY/TUNING MODE repeatedly until "PRESET" appears. To cancel the Automatic Tuning Press PLAY/TUNING MODE. Tips · You can switch from another source to the tuner by pressing TUNER BAND (Automatic Source Selection). · If you press TUNER BAND while the power is off, the power turns on and the system tunes in the last received station automatically (One Touch play). · To improve broadcast reception, reorient the supplied antenna or connect an optional external antenna (FM antenna only). · When an FM program has static noise, press STEREO/MONO until "MONO" appears. · "--. --" appears when the total playing time has exceeded 100 minutes, or when you select a track whose number is 21 or over. · If you try to program 33 or more tracks, "FULL" appears. · You can also select a CD by using DISC 1 ­ 5 on the unit in step 3. 17 Playing the CD tracks repeatedly -- Repeat Play You can repeat a disc or all discs in normal play, Shuffle Play and Program Play. Using the CD display You can check the total number of tracks, the total playing time, and the remaining time on the track or the CD. When a CD TEXT disc is loaded, you can check the information stored on the CD, such as the titles or artist names. 1 1 2 3 4 5 8 6 2 + ­ FUNCTION 1 2 3 DISPLAY 7 9 4 5 8 6 10/0 >10 7 N X x 9 ­ + 10/0 >10 + x . > M m N X ­ + ­ ­ + . > M m + ­ 1 2 Press FUNCTION repeatedly until "CD" appears. Press REPEAT during play until "REPEAT" or "REPEAT 1" appears. REPEAT: For all the tracks. REPEAT 1: For a single track only in normal play. To cancel Repeat Play Press REPEAT until "REPEAT" or "REPEAT 1" disappears. 18 Checking the total playing time Checking the remaining time , Press DISPLAY repeatedly during play. 1 2 Press FUNCTION repeatedly until "CD" appears. While the disc is stopped, press DISPLAY repeatedly. Each time you press the button, the display changes as follows: Each time you press the button, the display changes as follows: t The disc number, the track number and the elapsed time of the current track r The disc number, the track number and the remaining time*1 of the current track r The remaining time of the current CD*2 r The disc title of the current CD*3 r Clock The CD Player t The disc number and the track number r The disc title* r Artist name* r The total number of tracks and the total playing time (The number of programed tracks when programed) r Clock *1 "--. --" is displayed when the CD contains more than 20 tracks. *2 "--. --" is displayed in all modes except 1 DISC CONTINUE. When the disc title has more than 31 characters, not all the characters are displayed. * With CD TEXT discs only. [. . . ] · The face of the CD is scratched. · The CD is facing the wrong way. · Moisture condensation has built up. Remove the CD and leave the system turned on for about 2 hours until the moisture evaporates. [. . . ]