User manual SONY STP-XH70 DATASHEET

[. . . ] Notice for the customers in the U. S. A. Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. The following FCC statement applies only to the version of this model manufactured for sale in the U. S. A. Other versions may not comply with FCC technical regulations. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] When the system is changed to a function other than the Bluetooth function and BLUETOOTH OPR on the unit is pressed while connected to a Bluetooth device, it may take some time until a connection is made with the Bluetooth headphones. This system stores separate volume settings for when listening through the speakers or PHONES jack on the unit, or when listening through Bluetooth headphones. Select a function other than the Bluetooth function. Press FUNCTION repeatedly. Basic Operations Establish a connection with the Bluetooth headphones. Press and hold BLUETOOTH OPR on the unit for about 2 seconds until the BLUETOOTH indicator lights up, then release the button. If more than one Bluetooth device that has been connected in the past is present around the system, the system attempts to connect with up to 3 most recently connected devices. (Connection is attempted with up to 3 devices in order from the most recently connected device, and the attempts end when a connection is established. ) Once the connection is established, the system display changes as follows: "Connect" Name of the Bluetooth device 3 Start playback of the music for the function selected in step 1. Depending on the type of Bluetooth headphones, you can operate this system (playback, volume control, etc. ) using the headphone's controls. For details about the operations of the Bluetooth headphones, refer to the operation manual supplied with your Bluetooth headphones. 4 Adjust the volume. Press VOLUME +/ (or turn the VOLUME control on the unit) . GB Using optional audio components 1 Connect additional audio component to the AUDIO IN jack on the unit using an audio analog cord (not supplied). Turn down the volume. Adjusting the sound To add a sound effect To Generate a more dynamic sound (Dynamic Sound Generator X-tra) Set the sound effect Press DSGX on the unit. 2 3 4 5 Press VOLUME (or turn the VOLUME control on the unit) . Select the AUDIO IN function. Press AUDIO IN . Start playing the connected component. Adjust the volume. Press VOLUME +/ (or turn the VOLUME control on the unit) . EQ repeatedly to select "BASS" or "TREBLE, " and then press +/ repeatedly to adjust the level. GB Changing the display To Change information on the display1)2) Check the clock when the system is off 1) Press DISPLAY repeatedly when the system is on. The clock is displayed for 8 seconds. Basic Operations 2) 3) For example, you can view CD/MP3 disc information, such as the track or file number or folder name during normal play, or the total playing time while the player is stopped. You can also view XM or SIRIUS radio information, such as the channel name, song title and artist name. When the system and a Bluetooth device are connected using the Bluetooth function, you can view the Bluetooth device address. The STANDBY indicator on the unit lights up when the system is off. Notes on the display information Characters that cannot be displayed appear as "_". Use buttons on the remote to control the Play Timer. Make sure you have set the clock. Note Before the system is turned off, if a connection is made with the Bluetooth headphones, sounds played by the Play Timer may be output to the Bluetooth headphones. To activate or check the timer again 1 Prepare the sound source. Prepare the sound source, and then press VOLUME +/ to adjust the volume. To start from a specific track or file, create your own program (page 26). Press CLOCK/TIMER SELECT , press / repeatedly until "PLAY SEL?" appears, and then press ENTER . To cancel the timer Repeat the same procedure as above until "TIMER OFF?" appears, and then press ENTER . 2 3 Press CLOCK/TIMER SET . Press / repeatedly to select "PLAY SET?, " and then press ENTER . "ON TIME" appears, and the hour indication flashes. To change the setting Start over from step 1. Tip The Play Timer setting remains as long as the setting is not canceled manually. 4 5 GB Set the time to start playing. Press / repeatedly to set the hour, and then press ENTER . Use the procedure above to set the minutes. Use the same procedure as in step 4 to set the time to stop playing. Others Troubleshooting 1 Make sure the power cord and speaker cords are correctly and firmly connected. below, and take the indicated corrective action. If the issue persists, contact your nearest Sony dealer. Severe hum or noise. Move the system away from sources of noise. Connect the system to a different wall socket. Install a noise filter (available separately) to the power cord. [. . . ] Bluetooth standard profiles indicate the purpose of Bluetooth communication between devices. CD player section System: Compact disc and digital audio system Laser Diode Properties Emission duration: continuous Laser Output*: Less than 44. 6µW Others Amplifier section Continuous RMS power output (reference): 50 + 50 watts (6 ohms at 1 kHz, 10% THD) Inputs: AUDIO IN (stereo mini jack): voltage 250 mV, impedance 47 kilohms Outputs: PHONES (stereo mini jack): accepts headphones of 8 ohms or more SPEAKER: accepts impedance of 6 ohms Frequency response: 20 Hz 20 kHz Signal-to-noise ratio: More than 90 dB Dynamic range: More than 90 dB * This output is the value measurement at a distance of 200mm from the objective lens surface on the Optical Pick-up Block with 7mm aperture. Tuner section FM stereo, FM/AM superheterodyne tuner FM tuner section: Tuning range: 87. 5 108. 0 MHz (100 kHz step) Antenna: FM lead antenna Antenna terminals: 75 ohms unbalanced Intermediate frequency: 10. 7 MHz AM tuner section: Tuning range: 530 1, 710 kHz (with 10 kHz tuning interval) 531 1, 710 kHz (with 9 kHz tuning interval) Antenna: AM loop antenna, external antenna terminal Intermediate frequency: 450 kHz Bluetooth section Communication system: Bluetooth Standard version 2. 0 Output: Bluetooth Standard Power Class 2 Maximum communication range: Line of sight approx. 10 m1) Frequency band: 2. 4 GHz band (2. 4000 GHz 2. 4835 GHz) Modulation method: FHSS Compatible Bluetooth profiles2): A2DP (Advanced Audio Distribution Profile) AVRCP (Audio Video Remote Control Profile) Supported codecs: Receive: SBC (Sub Band Codec), MP3 Transmit: SBC (Sub Band Codec) Speaker (SS-CHX7) Speaker system: 2-way, 2-unit, bass-reflex type Speaker units: Woofer 12 cm, cone type, Tweeter 4 cm, cone type Nominal impedance: 6 ohms Dimensions (w/h/d): Approx. 145 × 260 × 200 mm Mass: Approx. 2. 2 kg net per speaker Continued GB General Power requirements: 120 V AC, 60 Hz Power consumption: 40 watts Dimensions (w/h/d) (excl. [. . . ]