User manual SONY SU-RS11M TV STAND - INSTRUCTIONS

[. . . ] · The USB-PSTN modem adaptor is a bus powered device and therefore requires no power supply. Trademark The system names and product names recorded in this instruction manual are in general registered trademarks or trademarks of their respective developing manufacturers. This instruction manual does not specify TM and ® signs. 3 Precautions on Use Where not to place this device Regardless of whether the USB-PSTN modem adaptor is in use or in storage, do not place it in any of the following locations. · Locations of extremely high temperature The temperature gets extremely high inside a car with the windows closed in summer or in strong sunshine, and leaving the USB-PSTN modem adaptor inside may cause it to be deformed or break down. · Locations with excessive humidity, dust, soot or steam Using the USB-PSTN modem adaptor in such an environment may lead to fire or electric shock. [. . . ] · Only use a designated connecting cable Using a connecting cable not specified in this manual may lead to fire or breakdown. · Avoid incorrect connection - Do not allow any small pieces of metal inside the connector. A short between pins may lead to fire or breakdown. - Insert the connector completely straight. Inserting it at an angle can cause a short between pins, which may lead to fire or breakdown. · Unplug the telephone cable before moving the USB-PSTN modem adaptor Moving it with the telephone cable still connected may damage the cable or lead to fire, electric shock, or injury if the USB-PSTN modem adaptor drops or falls over. Also be careful not to drop the USB-PSTN modem adaptor. · In direct sunlight or near a heater There is a risk of deformation or breakdown. · Locations of excessive vibration · Locations with strong electromagnetism · Locations with excessive sand In locations such as the seashore and other sandy areas or where dust clouds occur, protect the USB-PSTN modem adaptor from sand and dust. There is a risk of breakdown. 4 Precautions on Handling · Using the USB-PSTN modem adaptor reduces the amount of time you can use your camcorder, because they share the camcorder's battery. · When not using the USB-PSTN modem adaptor, disconnect it from your camcorder to prevent your camcorder's battery from going flat. To check the dial speed, switch the dial speed selector on the phone and check the clicking sound. When you select the fast dial speed, set the TONE/P1 (PULSE10)/P2 (PULSE20) selector to P2 (PULSE20). 8 The setup of the AREA CODE switches The default AREA CODE setting is "Japan". Set the AREA CODE switches to the appropriate positions using a sharppointed object following the information given in the table below. You cannot use the unit in areas other than the areas indicated on the table. TONE P1 P2 Notes · "1" for the parameter in the table indicates that setting the switch to the ON side. · The relationship between the 6-digit numbers in the table and the switch positions is as illustrated below. g. , when you set to the USA) The setup list for the AREA CODE switch Country or area Japan United States Australia Austria Belgium Denmark Finland France Germany Parameter 000000 100000 010000 110000 001000 111000 000100 100100 010100 Country or area Greece Ireland Italy Netherlands New Zealand Norway Portugal Singapore Spain Parameter 110100 101100 011100 010010 110010 001010 011010 111010 100110 Country or area Sweden Switzerland Taiwan United Kingdom Canada Hong Kong Luxembourg Parameter 010110 110110 001110 101110 100000 100000 001000 9 Preparation To connect to the Internet, first you must connect the USB-PSTN modem adaptor to a USB network adaptor-compatible camcorder. Connecting to a telephone line with a PSTN modem adaptor Connect to the Internet via a telephone line using a USB-PSTN modem adaptor. 1 Connect the telephone cable (not supplied) to this unit and the modular jack of the telephone. Note A telephone cable is not supplied with this USB-PSTN modem adaptor. Please prepare the telephone cable for the Australia / New Zealand domestic. 10 2 Attach the USB-PSTN modem adaptor's USB connector to (USB) jack of your camcorder. Note The position of (USB) jack varies from model to model. For details, refer to your USB network adaptor compatible camcorder's instruction manual. 3 Set your USB network adaptor compatible camcorder's power switch to "MEMORY/NETWORK" to display the Network Menu. Your camcorder is now ready for communication. Note Connect the USB-PSTN modem adaptor directly to your USB network adaptor compatible camcorder. The camcorder is not compatible with a USB hub. Accessing the Internet For details of how to log on, refer to your USB network adaptor compatible camcorder's "Network Function/Application Operating Instructions". 11 Disconnecting the USB-PSTN modem adaptor from your camcorder 1 Remove the USB-PSTN modem adaptor's USB connector from (USB) jack of your camcorder. 2 Remove the telephone cable from the USB-PSTN modem adaptor. 12 Troubleshooting Before sending the USB-PSTN modem adaptor for repairs, read this manual and the support information on our website http://www. sony. net/. If the USB-PSTN modem adaptor still does not work properly, consult your Sony dealer or local authorized Sony service facility. Symptom A USB error occurs ex) Connection Error Connect USB Device A PPP error occurs ex) Connection Error Check phone line Cause/Measures · Check that the USB-PSTN modem adaptor is correctly connected to the USB terminal of your USB network adaptor compatible camcorder. · The AREA CODE switch is incorrectly set. [. . . ] · The AREA CODE switch is incorrectly set. For details, see "Setting up the unit" (page 7). (Another device is using the phone line. ) c Try again when the other device has stopped communicating. · Cannot connect to the other telephone line. [. . . ]